Trango Systems M2400S User Manual Download Page 45 | Manualshive

Page: 45 / 50

background image

Trango Broadband Wireless — User Manual M2400S Rev. A

Page

41

Command Radio

Description

Access

pppoeonly

SU

Display current PPPoE filter setting

ro/rw

pppoeonly <on | off>

SU

Change PPPoE filter setting
With PPPoE filter set to ON, only PPPoE packets will pass Default:
off – Pass All Packets

rw

reboot AP/SU

Reboot

unit

ro/rw

remarks AP/SU

Display

remarks

ro/rw

remarks <str,31 octs>

AP/SU

Overwrite remarks

rw

reset

AP/SU

Reset radio’s system settings back to factory defaults, then reboot

rw

rfrxth

AP/SU

Display current RF RX Threshold

ro/rw

rfrxth <-98..-55>

AP/SU

Change current RF RX Threshold
default = -98 dBm

rw

rssi

AP/SU

Display current RX RSSI for packets received during a 1s window
Opmode “OFF” only on AP

ro/rw

save <mainimage | fpgaimage> <current
chscksum> <new checksum>

AP/SU

Save new firmware. This command gets new firmware image from
TFTP buffer, verifies checksum and writes to flash memory at main
or FPGA image section.

rw

save sudb

AP

Save SUDB into flash memory

rw

save <systemsetting | ss>

AP/SU

Save current configuration into flash memory

rw

set apid <ap-id>

AP

Set AP ID, <ap-id> = 1..255

rw

set baseid <base-id, 4 oct>

AP/SU

Set base station id Base ID = XXXX where X = any alphanumeric
character except “/”

rw

set defaultopmode <on | off>

AP/SU

Set default Opmode to “ON” or “OFF”
Factory set default Opmode is “OFF”

rw

set httpport [<port #>]

AP/SU

Set or display HTTPD port number
port # = 1..65534

default port = 80

rw

set snmpcomm <read | write | trap id# |trap all>

AP/SU

Set SNMP read or write or trap community string

rw

set telnetport [<port #>]

AP/SU

Specify telnet port, <port #> = 1..65534

Default port = 23

rw

snmpsample <min, 1..60>

AP/SU

Set SNMP sample period

rw

su password <suid | all> <rw | ro> <new
password> <new password>

AP

Change read/write or read-only password of all or a specific
subscriber

rw

su <all | suid>

AP

Display all or specific SU information in SUBD

ro/rw

su info <suid>

AP

Command issued from the AP to gather information about specific
SUs.

1. Distance
2. RSSI at AP
3. RSSI at SU
4. IP

address

5. Subnet

address

6. Gateway

address

7. Device

ID

8. Hardware

version

9. FPGA

version

10. FPGA checksum
11. Firmware version
12. Firmware checksum
13. Firmware datecode
14.  Broadcast/multicast packet filter on/off
15.  Auto scan AP on/off
16.  TCP/IP for AP on/off
17. HTTPD on/off
18.  TCP/IP service for Ethernet port on/off
19.  Default channel and antenna
20.  Active channel and antenna
21. TX power

ro/rw

«
...
43
44
45
46
47
...
»

Summary of Contents for M2400S



















































Reviews:

No comments

Related manuals for M2400S

Brand: Ubiquiti Pages: 36

Brand: OBERON Pages: 2

STEVAL-SPBT4ATV3

Brand: ST Pages: 9

Brand: iBall Baton Pages: 71

WL-ICNAP48F-060

Brand: Mach Power Pages: 22

Brand: H3C Pages: 32

Brand: SIYI Pages: 28

Brand: SoftBank Pages: 231

Brand: Aztech Pages: 67

IGAP-420 series

Brand: ORiNG Pages: 56

Brand: ORiNG Pages: 58

Videomesh 2200 Series

Brand: Fluidmesh Pages: 30

ARS-7235-PSE-AC Series

Brand: ANTAIRA Pages: 24

Brand: Draytek Pages: 140

Brand: Gigafast Pages: 24

Bell U998 Turbo Stick

Brand: Novatel Pages: 19

Brand: Rittal Pages: 20

EnterprisePro R-3300

Brand: Redlion Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands