Trango Systems M2400S User Manual Download | Manualshive

Page: 13 / 50

background image

Getting

Started

Trango Broadband Wireless — User Manual M2400S Rev. A

Page

9

Link Control:

This page shows which SUs are associated. This page also provides several tools for evaluating the

quality of the wireless link.

Command Console:

From this page, the user can run any console command that is not interactive (i.e.

ipconfig

)

or time sensitive (

su linktest

). For a complete list of console commands, type

help

or

?

in the entry field.

Logout:

This link will end the current browser session with the radio.

Help:

The Browser Interface features useful Help pages which explain all listed parameters. To access the help

pages click on the Help link.

Command Line Interface

Although most radio functions can be managed via the browser interface, the command line interface (CLI)
provides slightly more functionality and is usually the management tool of choice for experienced users. The CLI
can be accessed through Telnet.

Telnet

Open a command prompt (DOS) session on your PC. Open a telnet session by typing:

telnet [ip address of radio]

All Trango radios are pre-configured at the factory with a default IP address of 192.168.100.100. The factory
default password is

trango

.

Once you connect to the radio you will be greeted with current hardware and firmware

information and prompted for a password. Type in the read-write (RW) password and press enter.

Example:

C:>telnet 192.168.100.100
Welcome to Trango Broadband Wireless M2400S-AP 1p0X21H0006D04081903
Password:
#>

To terminate a CLI session (Telnet or Serial) type the command

logout

.

!

Note: Type

help

or

?

for a listing of all CLI commands. Type

help <command>

for the syntax of a particular

command.

Example (to view a list of all commands that start with su)

#> ? su
su [all | <suid, 1..126>]
su info <suid, 1..126>
su linktest <suid, 1..126>
su password <suid|all> <rw|ro> <new password> <new password>
su ping <suid, 1..126>
su reboot <suid|all>
su sw <suid|all> <sw#, 0..7> <on | off>
su testrflink <suid, 1..126> <r>
su testrflink <all> <r>
sudb add <suid, 1..126> <pr|re> <device id,hex>
sudb cirmir <<suid>|all> <cir dn> <cir up> <mir dn> <mir up>
sudb defaultcirmir [<cir dn> <cir up> <mir dn> <mir up>]
sudb delete <<suid>|all>
sudb dload
sudb gid <<suid>|all> <0..15>
sudb view
survey <time, 1..10 sec> <antenna, h|v|e>

«
...
11
12
13
14
15
...
»

Summary of Contents for M2400S



















































Reviews:

No comments

Related manuals for M2400S

Brand: Cerio Pages: 13

HT-TM01 TripMate

Brand: Hootoo Pages: 47

Brand: NETGEAR Pages: 60

AIR-CAP3501E-A-K9

Brand: Cisco Pages: 34

AIR-AP1210 - Aironet 1200 - Wireless Access Point External

Brand: Cisco Pages: 35

Aironet 1520 Series

Brand: Cisco Pages: 66

Brand: Cisco Pages: 44

AIR-CAP1552H-x-K9

Brand: Cisco Pages: 24

AIR-AP1542D-*-K9

Brand: Cisco Pages: 72

AIR-AP1010 - 1000 Series Lightweight Access Point

Brand: Cisco Pages: 36

AIR-BR1310G-A-K9 - Aironet 1310 Outdoor Access Point/Bridge

Brand: Cisco Pages: 14

AIR-AP1232AG-A-K9 - Aironet 1230AG - Wireless Access Point

Brand: Cisco Pages: 8

1231G - Aironet - Wireless Access Point

Brand: Cisco Pages: 126

AIR-AP1251AG-A-k9

Brand: Cisco Pages: 140

AIR-AP1210 - Aironet 1200 - Wireless Access Point External

Brand: Cisco Pages: 160

Brand: Cisco Pages: 28

Aironet 1300 Series

Brand: Cisco Pages: 34

Brand: Cisco Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands