Trango Systems M2400S User Manual Download | Manualshive

Page: 38 / 50

background image

Deployment

Trango Broadband Wireless — User Manual M2400S Rev A

Page

34

[001]
Ping #0 -> -52 dB 220 us 0.0 mi
Ping #1 -> -53 dB 219 us 0.0 mi
Ping #2 -> -53 dB 220 us 0.0 mi
Ping #3 -> -52 dB 220 us 0.0 mi
Ping #4 -> -53 dB 219 us 0.0 mi
Ping #5 -> -52 dB 220 us 0.0 mi
Ping #6 -> -50 dB 220 us 0.0 mi
Ping #7 -> -52 dB 220 us 0.0 mi
Ping #8 -> -52 dB 220 us 0.0 mi
Ping #9 -> -52 dB 220 us 0.0 mi
[#End]
Avg = -51 dB
Success.

su <suid>

AP will poll the SU for SU’s current status and will provide information such as SU range from AP, signal strength
received at SU from AP, SU temperature, etc.

Example:
#> su 1
[  1] pr [as] y [d] 0.0 [rssi at ap] -50 dBm [rssi at su] -60 dBm
       [ip] 10.8.1.234 [subnet] 255.255.255.192 [gateway] 10.8.1.193
       [mac] 00 01 DE 19 F0 A4
       [hw ver] 0006 [fpga ver] 04042201 [fpga chksum] 47231EEE
       [fw ver] 1p0x8 [fw chksum] 6DDF232C [fw datecode] 04061502
       [default channel and antenna] 1 h [active channel and antenna] 1 h
       [tx power] 23 dBm
       [ch#1] 2405 [ch#2] 2415 [ch#3] 2425 [ch#4] 2435 [ch#5] 2445 [ch#6] 2455

[ch#7] 2465 [ch#8] 2475

       [remarks]
       [RF Tx Retry at AP] 0 [RF Tx Retry Maxed Out at AP] 0
       [RF Tx Retry at SU] 0 [RF Tx Retry Maxed Out at SU] 0
Success.

#>

su linktest <suid>

This command checks the integrity of the wireless link from the standpoint of performance (throughput) and over-the-air
packet loss. The AP will send 100 1600 byte packets to the SU, and the SU will return the packets it receives to the AP.
A perfect link (without dropped packets) will yield average throughput of 5,000 Kbps. If heavy packet loss occurs it may
be caused by interference or multi-path.

Example:

#> su linktest 1
[suid] 1 [pkt len] 1600 bytes [# of pkts per cycle] 100 [cycle] 10

0 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0  [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0  5
00 ms  5120 kbps
1 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0  [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0  5
00 ms  5120 kbps
2 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0  [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0  5
00 ms  5120 kbps
3 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0  [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0  5
00 ms  5120 kbps

«
...
36
37
38
39
40
...
»

Summary of Contents for M2400S



















































Reviews:

No comments

Related manuals for M2400S

Brand: BEC Pages: 18

Brand: Ubiquiti Pages: 24

Brand: TCL Pages: 23

Skyr@cer USB 4101GMR

Brand: Topcom Pages: 212

DECT 1615 Series

Brand: Uniden Pages: 28

Brand: Pronto Pages: 14

Brand: Loopcomm Pages: 66

Brand: Loopcomm Pages: 83

Brand: Billion Pages: 230

Brand: Linksys Pages: 155

Brand: Billion Pages: 2

Brand: Invoxia Pages: 19

Brand: Yunlink Pages: 33

Brand: Air Live Pages: 3

NetGenie SOHO N300

Brand: Cyberoam Pages: 81

Brand: EnGenius Pages: 4

Brand: EnGenius Pages: 64

Brand: P2 Wireless Technologies Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands