Trango Systems M2400S User Manual Download

Page: 31 / 50

Basic

Configuration via CLI

Trango Broadband Wireless — User Manual M2400S Rev A

Page

SU SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS

SU Parameter

Description

Related CLI Command

#>freq 3

This command will change the channel of the AP to
3. Use the antenna command to select an antenna
polarization.

antenna [<h | v |e>]

Broadcast Packet Filter

This software switch (0)
enables/disables the blocking
of Ethernet control packets,
except ICMP and ARP, to
reduce the amount of
unnecessary overhead
introduced into the wireless
link. Default setting is ON.

sw 0 [<on|off>]

Example:

#>sw 0 on

AP Autoscan

This software switch (1) is to
turn AP autoscan on or off.

sw 1 [<on|off>]

(default is on)

TCP/IP for AP

This software switch (2)
when on, allows users at the
AP side of the network to
telnet or HTTP into the SU.

sw 2 [<on|off>]

(default is on)

Example:

#>sw 2 off

TCP/IP for Local
Ethernet Port

This software switch (6)
when on, allows users on the
wired side of the SU to telnet
or HTTP into the SU
regardless of the Opmode.

sw 6 [<on|off>]

(default is on)

Remarks User

definable

radio

information (i.e. customer
name, address of installation,
and so on). A maximum of
28 characters can be stored.

remarks [<remarks>]

Example:

#>remarks 678 Oak Ave

Counters:
RF TX RF RX
Eth TX Eth RX

This is an average of wired
and wireless, transmitted and
received, traffic in kilobits
per second.

Informational Parameter

Summary of Contents for M2400S



















































Search results

Summary of Contents for M2400S

Reviews:

Related manuals for M2400S

Brands by name

Popular brands

Trango Systems M2400S, User Manual

Search results

Summary of Contents for M2400S

Reviews:

Related manuals for M2400S

Brands by name

Popular brands