Trango Systems M2400S User Manual Download Page 20 | Manualshive

Page: 20 / 50

background image

Basic

Configuration via Browser Interface

Trango Broadband Wireless — User Manual M2400S Rev A

Page

16

LED Summary

At this point it is useful to learn about the various LEDs that can be found on the bottom of the radio. These LEDs
can assist the user in determining radio and link status.

ASSOCIATION LED (GREEN)

Blinking once every second in
Opmode "OFF" (AP and SU).

Twice per second Opmode "ON" and
scanning for an AP (SU Only).

Solid after unit is associated with an
AP (SU Only).

Solid after unit is in Opmode "ON" (AP
Only).

ACT LED (RED)

- Ethernet Activity Light

10/100 Link LED (GREEN)

-

Illuminated when link speed is
negotiated at 100 BaseT. It is off
when link speed is 10 BaseT or not
connected.

RSSI LEDs (YELLOW)

- In all modes except "Survey,"

the unit's four yellow LEDs indicate the level of RF
signal being received from a valid AP.

Yellow LED 1 (rightmost): On when RSSI > -85 dBm
Yellow LED 2 : On when RSSI > -75 dBm
Yellow LED 3 : On when RSSI > -65 dBm
Yellow LED 4 (leftmmost): On when RSSI > -55 dBm.

In addition, these 4 LEDs will flash once to indicate the
'factory reset' button has been activated.

RESET BUTTON - resets IP and

password to factory default

Figure 7: LED Summary

Link Control Page

The radio’s firmware includes several useful tools to assist in determining which SUs are associated, and the
quality of each link. One method for verifying link quality is by using the Link Control page.

LED / RESET BUTTON WINDOW

«
...
18
19
20
21
22
...
»

Summary of Contents for M2400S



















































Reviews:

No comments

Related manuals for M2400S

Brand: Quantum Pages: 8

Brand: Quantum Pages: 21

Brand: Quantum Networks Pages: 27

Brand: Gemtek Systems Pages: 13

Brand: Ubiquiti Pages: 13

Brand: Cisco Pages: 90

EKI-6333AC-A Series

Brand: Advantech Pages: 42

CradlePoint PHS300tw

Brand: Cradlepoint Pages: 2

Brand: Astronics Pages: 56

Brand: Air Live Pages: 171

Brand: Air Live Pages: 161

Road Runner Mobile

Brand: Sierra Wireless Pages: 9

Brand: Sierra Wireless Pages: 11

Brand: Sierra Wireless Pages: 74

Brand: Xclaim Pages: 4

Brand: GL Technologies Pages: 2

Brand: RFNet Pages: 22

Brand: Draytek Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands