Trane Arctic PolyTherm TM Series, Installation, Operation And Maintenance Manual

Page: 10 / 84

10 ARTC-SVX005B-EN
Trane will document and photograph the status of the
unit prior to shipment and carry out the instructions
detailed in the factory order regarding in-shop
preparation of units for long-term storage.
Customer Responsibilities
Upon receipt of a chiller system, the customer must
conduct thorough internal and external inspections,
removing packaging material as needed for access to
all components.
Visible damage must be noted on the signed and dated
bill of lading. The customer may request a carrier
inspection by telephone or in person, but any such
request should be confirmed in writing. It is
recommended that the customer request that the
carrier inspect the damage within 72 hours of
notification.
The customer must store the chiller system in a dry,
non-corrosive, dust- and vibration-free environment
due to the exposure sensitivities of the microprocessor
controllers and to prevent electrical terminations from
deteriorating from non-use. Conditions in storage
locations should not fall below -20 °F (-29 °C) or exceed
150 °F (66 °C).
Components sealed in plastic shrink-wrap are not
exempt from these storage requirement. Moisture can
potentially collect inside the plastic film, resulting in
corrosion of the cabinet and electronic components.
Any chiller system packaging that is removed must be
replaced with similar protective covering as soon as
possible.
Failure to adhere to these long-term storage
requirements may void the Trane warranty. Any
component that is damaged or inoperable due to
improper storage may have its warranty voided.
Chiller Dimensions
Depending upon the number of modules, the
assembled chiller will occupy the dimensions shown in
Figure 2, p. 11 and Table 2, p. 11 , depending upon the
rated tonnage of the chiller modules.
W WA AR RN NIIN NG G
E Elle eccttrriicca all S Sh ho occkk,, E Ex xp pllo ossiio on n,, o orr A Arrcc
F Flla assh h H Ha azza arrd d!!
F Fa aiillu urre e tto o ffo ollllo ow w tth he esse e iin nssttrru uccttiio on nss cco ou ulld d rre essu ulltt iin n
d de ea atth h o orr sse erriio ou uss iin njju urry y..
•• IIn nsstta allll tth he e p prro od du ucctt iin n a an n a ap pp prro op prriia atte e
e elle eccttrriicca all//ffiirre e e en nccllo ossu urre e p pe err llo occa all
rre eg gu ulla attiio on nss.. D Do o n no ott iin nsstta allll tth he e p prro od du ucctt iin n
h ha azza arrd do ou uss o orr cclla assssiiffiie ed d llo occa attiio on nss..
•• D Do o n no ott u usse e tth he e p prro od du ucctt ffo orr lliiffe e o orr ssa affe etty y
a ap pp plliicca attiio on nss..
•• D Do o n no ott e ex xcce ee ed d tth he e p prro od du ucctt rra attiin ng gss o orr
m ma ax xiim mu um m lliim miittss.. P Prro od du uccttss rra atte ed d o on nlly y ffo orr
b ba assiicc iin nssu ulla attiio on n m mu usstt b be e iin nsstta alllle ed d o on n
iin nssu ulla atte ed d cco on nd du ucctto orrss..
•• C Cu urrrre en ntt ttrra an nssffo orrm me err sse ecco on nd da arriie ess ((ccu urrrre en ntt
m mo od de e)) m mu usstt b be e ssh ho orrtte ed d o orr cco on nn ne ecctte ed d tto o a a
b bu urrd de en n a att a allll ttiim me ess..
•• R Re em mo ov ve e a allll w wiirre e ssccrra ap pss,, tto oo ollss,, rre ep plla acce e a allll
d do oo orrss,, cco ov ve errss a an nd d p prro otte eccttiiv ve e d de ev viicce ess b be effo orre e
p po ow we erriin ng g tth he e e eq qu uiip pm me en ntt..
W WA AR RN NIIN NG G
P Prro op pe err F Fiie elld d W Wiirriin ng g a an nd d G Grro ou un nd diin ng g
R Re eq qu uiirre ed d!!
F Fa aiillu urre e tto o ffo ollllo ow w cco od de e cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
A Allll ffiie elld d w wiirriin ng g M MU US ST T b be e p pe errffo orrm me ed d b by y q qu ua alliiffiie ed d
p pe errsso on nn ne ell.. IIm mp prro op pe errlly y iin nsstta alllle ed d a an nd d g grro ou un nd de ed d
ffiie elld d w wiirriin ng g p po osse ess F FIIR RE E a an nd d E EL LE EC CT TR RO OC CU UT TIIO ON N
h ha azza arrd dss.. T To o a av vo oiid d tth he esse e h ha azza arrd dss,, y yo ou u M MU US ST T ffo ollllo ow w
rre eq qu uiirre em me en nttss ffo orr ffiie elld d w wiirriin ng g iin nsstta alllla attiio on n a an nd d
g grro ou un nd diin ng g a ass d de essccrriib be ed d iin n N NE EC C a an nd d y yo ou urr llo occa all//
sstta atte e//n na attiio on na all e elle eccttrriicca all cco od de ess..
Handling of the Modules
The packaging from the factory permits lifting with a
suitable crane. Ensure straps are in good working
condition and that they are rated for the weight of the
machines. Spreader bars may be required for effective
rigging and to avoid damage to the chiller/heater
modules.
The chiller modules arrive fully charged with
refrigerant. As required under Federal regulations,
installation, start-up and service should be performed
by fully-qualified, factory-certified, personnel.
G Ge en ne erra all IIn nffo orrm ma attiio on n