4-10
Replacing XRC-195 Board
The XRC-195 Board is mounted to the backside of access door. It is mounted, to the door,
on standoffs. Refer to Figure 4–1 or Figure 4–2.
The XRC-195 Board, as with any electronic board, is susceptible to
damage by static electricity or improper handling. To prevent this from
occurring, user should wear a grounding strap.
A grounding strap is a conductive device used to make connection
between the person handling the board, and a high quality ground point.
Before handling the board you must install ground strap on your body
then connect it to a grounded point. This discharges electrical static
buildup from the body to ground, preventing static from discharging to the
board.
Before removal of XRC-195 Board, be certain any data has been saved
to an external storage medium. Failure to do so could result in data loss
when XRC-195 Board is removed.
Procedures
In the following procedure, the common name for a component, its
jumper number if available (Abbreviated J) or part is followed by a
number in parentheses.
Step Procedure
1.
Before XRC-195 Board (see Figure 4–1 or Figure 4–2, Item 10)
removal, disconnect the following associated connectors in this
order.
•
If used, disconnect external charging source J17 (see
Figure
4–5
Item 21).
•
Disconnect battery pack connector J16 (Item 22).
•
Slide out to the right; the following green terminal strips from
its associated XRC-195 Board connector. DO NOT lift
connectors upward. Tape an identifier to each connector so
it will be correctly reinserted into the same Board mounting
connector during reinstallation of XRC-195 Board.
J6-COMM 2 (Item# 18)
J6-COMM 1 (Item # 17)
J8-B (Item# 16)
J8-A (Item# 15)
J20 (Item# 13)
J23 (Item# 11)
•
Disconnect PCCU Port connector J15 (Item# 25).
•
LCD Interface connector J13 (Item# 24).
•
Remove cable from J18 (Item# 23) if External I/O Modules
are installed.
Continued on Next Page
Summary of Contents for XRC6490
