Topdon Phoenix Pro User Manual Download

Page: 84 / 142

Phoenix Pro User Manual

Information” box every time you save the diagnostic report.

8.11.3 Printer Set

This option is designed to establish a wireless connection between Phoenix Pro
and the Wi-Fi printer (sold separately) while performing printing operations.

Follow the steps below to connect the printer.

1. Tap “Printer Set”.

Fig. 8-9

A. If it is the first time you have operated this printer, please proceed the
following:

2. For initial use, you are suggested to reset the printer: Press and hold [MODE]

& [FEED] for 8 seconds, the following resetting command will be printed out:

at + default = 1

at + reboot = 1

rebooting...

1. Tap “Reset” to configure Wi-Fi printer.

Summary of Contents for Phoenix Pro















































































































































Search results

Summary of Contents for Phoenix Pro

Reviews:

Related manuals for Phoenix Pro

Brands by name

Popular brands

Topdon Phoenix Pro, User Manual

Search results

Summary of Contents for Phoenix Pro

Reviews:

Related manuals for Phoenix Pro

Brands by name

Popular brands