Topdon Phoenix Pro User Manual Download

Page: 110 / 142

Phoenix Pro User Manual

101

indicator

10 Running

indicator

It remains steady green after the Scopebox
is running.

11 Power

indicator

It keeps steady red after the Scopebox is
powered on.

12.2.2 Scopebox accessories

The Scopebox includes the secondary pickup cable for 4-channel oscilloscope,
crocodile clips for 4-channel oscilloscope, etc. See Table 12-2.

As the product configuration can be different, the accessories included with the
product may differ from the accessories listed on this manual. Please see the
packing list attached to the product for the detailed accessories.

Table 12-2 Accessory checklist

No.

Name

Picture

Secondary ignition pickup for
4-channel oscilloscope

Crocodile clips for 4-channel
oscilloscope

Direct ignition extension cable

6-way universal guide line for
4-channel oscilloscope

BNC to 4mm connector test cable

Summary of Contents for Phoenix Pro















































































































































Search results

Summary of Contents for Phoenix Pro

Reviews:

Related manuals for Phoenix Pro

Brands by name

Popular brands

Topdon Phoenix Pro, User Manual

Search results

Summary of Contents for Phoenix Pro

Reviews:

Related manuals for Phoenix Pro

Brands by name

Popular brands