manualshive.com logo in svg

Topdon Phoenix Pro, User Manual

Share
Download
Topdon Phoenix Pro User Manual Download Page 34

 

                                    

Phoenix Pro User Manual

 

25 

1.  Locate vehicle’s DLC socket.   

2.  Select the corresponding non-16pin connector. 

3.  Plug the non-16pin end of the connector into the DLC socket, and the other 

end to the OBD I adaptor, and then tighten the captive screws. 

4.  Connect the other end of the adaptor to the included VCI connector. 

5.  To supply power to OBD I adaptor from: 

A. Cigarette Lighter Cable: Connect one end of the cigarette lighter cable to 
vehicle’s cigarette lighter receptacle, and the other end to the power jack of 
OBD I adaptor.

 

 

Fig. 4-12 

B. Battery Clamps Cable: Connect one end of the battery clamps cable to 
vehicle’s battery, and the other end to the power jack of OBD I adaptor. 

   

Fig. 4-13 

4.5 Bluetooth Setting 

There are two kinds of ways available for the tablet to pair with the VCI 
connector. 

1. Connect one end of the USB cable (optional) to the Mini USB port of the VCI 

connector. 

Summary of Contents for Phoenix Pro















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands