Topdon Phoenix Pro User Manual Download

Page: 135 / 142

Phoenix Pro User Manual

126

14 Others

14.1 Email

The function allows you to send and receive email.

14.1.1 Configure an email account

*Note: Before sending or receiving email, you have to set up an email account. In

addition, this function required a stable network connection.

1. On the home screen, tap

Email

2. Choose the desired email account type.

3. Input email address and password, tap “Next”.

*Note: If “Manual setup” is selected, please consult your email service provider for

detailed parameter setting.

4. Follow the on-screen instructions to proceed until the system prompts you

that the account setup has been finished.

14.1.2 Add an email account

1. Tap

Settings

Accounts

2. Tap

Add account

3. Choose the desired account type.

14.2 Synchronization

You can transfer media files and APK between the PC and the tablet.

14.2.1 Connect to PC

1. Use the USB cable to connect the tablet to your PC.

2. Swipe from the top, a message “Connected as a media device” appears.

14.4.2 Run on PC

Perform the following steps:

Locate the new disc.

Copy

the

files.

Summary of Contents for Phoenix Pro















































































































































Search results

Summary of Contents for Phoenix Pro

Reviews:

Related manuals for Phoenix Pro

Brands by name

Popular brands

Topdon Phoenix Pro, User Manual

Search results

Summary of Contents for Phoenix Pro

Reviews:

Related manuals for Phoenix Pro

Brands by name

Popular brands