Topdon Phoenix Pro User Manual Download

Page: 17 / 142

Phoenix Pro User Manual

It illuminates Red while the connector is

plugged into the vehicle’s DLC.

Blue indicates it is working in Bluetooth

mode.

It illuminates Green when the connector is

connected to the tablet via USB cable.

2.3 Package List

Common accessories for each Phoenix Pro are same, but for different
destinations, the accessories of Phoenix Pro may vary. Please consult from the
local agency or check the packing list supplied with Phoenix Pro together.

No.

Item

Description

Qt.

Phoenix Pro tablet

For analyzing the vehicle data and

indicating the test results.

2 VCI

connector

For connecting to vehicle’s OBD II DLC to

access vehicle’s live data.

OBD II extension
cable

For connecting the VCI connector for

extension purpose.

OBD I adaptor

For connecting the non-16pin connector to

the VCI connector.

Cigarette lighter cable

Optional. To supply power to the

non-16pin connector through connection to

the vehicle’s cigarette lighter receptacle.

Battery clamps cable

Optional. To supply power to the

non-16pin connector through connection to

the vehicle’s battery.

7 Power

adaptors

1 for America area and 1 for Europe area

8 USB

cable

For connecting the VCI connector to

Phoenix Pro to perform vehicle diagnosis.

Summary of Contents for Phoenix Pro















































































































































Search results

Summary of Contents for Phoenix Pro

Reviews:

Related manuals for Phoenix Pro

Brands by name

Popular brands

Topdon Phoenix Pro, User Manual

Search results

Summary of Contents for Phoenix Pro

Reviews:

Related manuals for Phoenix Pro

Brands by name

Popular brands