THOMSON ST 2030 SIP Administrator'S Manual Download Page 162

Page: 162 / 316

ST2030s VoIP Business Phone

ST2030s SIP Administrator Guide v3.0

Page 154 of 308

Blind Transfer

When the user initiates a blind transfer, the phone launches

a “recovery

timer”. This timer ends if the 2nd correspondent answers and transfer is

then completed or if first dialog is recovered due to failure in the transfer or
timer expiration.

During this timer, in current implementation the transfer is not able to
answer to any incoming call, which is not a desirable behaviour in many

environments.
When an incoming call arrives, it is automatically placed on the first

available line. If the user press “C” key, an early BYE shall be sent to end

the dialog with the 1st correspondent.

Now, the early BYE must be sent only after the transferee has accepted the

REFER to avoid to cancel the on-going transfer.

Doing that, it is assumed there‟s no way to recover the 1st call if, for any

reason, the transfer fails.

The display will show the incoming call screen. Then the user can answer to

the 2nd call

See example below:

Summary of Contents for ST 2030 SIP





























































































































































































































































































































Search results

Summary of Contents for ST 2030 SIP

Reviews:

Related manuals for ST 2030 SIP

Brands by name

Popular brands

THOMSON ST 2030 SIP, Administrator'S Manual

Search results

Summary of Contents for ST 2030 SIP

Reviews:

Related manuals for ST 2030 SIP

Brands by name

Popular brands