Thermo Scientific KingFisher Flex Service Manual Download Page 69 | Manualshive

Page: 69 / 228

background image

Routine Operation

How to start

Thermo Fisher Scientific

Thermo Scientific KingFisher

®

Flex User Manual

63

Figure 4–43.

Shield plate in function

6.

Close the sliding door. The see-through lid (if in place) protects the
instrument against environmental contamination.

Note

The sliding door can be left open or the see-through lid can be

absent if desired. This action does not break the run.

▲

7.

After the run, remove the plate(s) according to the protocol request.
Confirm each plate removal by pressing the

START

key. Note that

the plate containing your samples is removed first.

8.

Press the

STOP

key after completing the run.

For startup, refer to “Switching on” on page 40.

Figure 4–44.

KingFisher Flex plates

The KingFisher Flex is compatible with KingFisher 24 Deep Well
plates, Microtiter 96 Deep Well plates, KingFisher 96 plates, and PCR
plates (Figure 4–44 and Table 4–4). Specially designed magnetic rods
(KingFisher Flex heads) and tip combs that protect the magnets during
the process are available for different plate types and applications.

Shield plate

«
...
67
68
69
70
71
...
»

Summary of Contents for KingFisher Flex





































































































































































































































Reviews:

No comments

Related manuals for KingFisher Flex

Brand: Landoll Pages: 34

Brand: Landoll Pages: 52

Brand: Gason Pages: 110

Brand: Gainsborough Pages: 2

Brand: ACDC Pages: 4

Precision2 HP2 Series

Brand: B-K lighting Pages: 6

Brand: Zero Hand Truck Pages: 38

Brand: B-K lighting Pages: 3

Brand: made for movement Pages: 51

Brand: Fellowes Pages: 20

Brand: IDEAL Networks Pages: 10

Brand: Pari Pages: 282

ST70 Instrument

Brand: Raymarine Pages: 12

Brand: Raven Pages: 73

Brand: Tascam Pages: 3

Brand: RAB Lighting Pages: 4

Brand: campgo Pages: 33

EVENTWASH VL800

Brand: Vari Lite Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands