Thermo Scientific KingFisher Flex Service Manual Download Page 47

Page: 47 / 228

Routine Operation

Control panel

Thermo Fisher Scientific

Thermo Scientific KingFisher

Flex User Manual

To pause the run. It will pause at the end of the ongoing processing
step.

To rotate the turntable clockwise (

TURNTABLE ROTATING CLOCKWISE

button).

To rotate the turntable counterclockwise (

TURNTABLE ROTATING

COUNTERCLOCKWISE

button).

The liquid crystal display is a 240 x 360 pixel display.

The main view in the display is shown in Figure 4–31.

Figure 4–31.

Main view on the display of the KingFisher Flex

There are three

menus

in the KingFisher Flex user interface:

Factory

protocols

User protocols

and

Maintenance

. In routine use you

mainly navigate in the

Factory/User protocols

menu. In advanced

level options there is one extra menu,

Maintenance

. You can navigate

between these three menus using the

Left

and

Right

arrow keys.

The

main view row

is either colored (active) or uncolored/different

colored (inactive).

All the descriptive

icons

used in the main view are shown in Table 4–3

below.

The

info text bar

shows explanatory information on how to proceed and

which keys to use.

This section visualizes navigation in the KingFisher Flex user interface.

The main view changes according to the selections you make either
with the

Down

arrow keys or the

button. The available

buttons and their function are shown on the info text bar.

Display

Navigating

Info text bar

Main view row

Icon

Summary of Contents for KingFisher Flex





































































































































































































































Search results

Summary of Contents for KingFisher Flex

Reviews:

Related manuals for KingFisher Flex

Brands by name

Popular brands

Thermo Scientific KingFisher Flex, Service Manual

Search results

Summary of Contents for KingFisher Flex

Reviews:

Related manuals for KingFisher Flex

Brands by name

Popular brands