Thermo Scientific KingFisher Flex Service Manual Download Page 20

Page: 20 / 228

Introduction to the KingFisher Flex

Advantages of using KingFisher Flex

Thermo Scientific KingFisher

Flex User Manual

Thermo Fisher Scientific

The KingFisher Flex magnetic particle processor has several operational
advantages:

●

Enables automation of complicated manual steps

●

Enables simultaneous processing and purification

●

Binding and elution are enhanced due to the heating option

●

Enables concentration of the sample during processing

●

Facilitates a good collection of bead-bound sample due to the
efficiency of the magnet

●

Enables a quicker reaction and a more efficient wash due to the
technology of moving magnetic particles instead of liquids

●

No carryover

●

No cross contamination

●

Facilitates the whole processing with the aid of an internal
program/BindIt Software.

Advantages of

using KingFisher

Flex

Summary of Contents for KingFisher Flex





































































































































































































































Search results

Summary of Contents for KingFisher Flex

Reviews:

Related manuals for KingFisher Flex

Brands by name

Popular brands

Thermo Scientific KingFisher Flex, Service Manual

Search results

Summary of Contents for KingFisher Flex

Reviews:

Related manuals for KingFisher Flex

Brands by name

Popular brands