Thermo Scientific KingFisher Flex Service Manual Download Page 41 | Manualshive

Page: 41 / 228

background image

Installation

How to pack the instrument for transportation

Thermo Fisher Scientific

Thermo Scientific KingFisher

®

Flex User Manual

35

It is recommended that you carry out a check run using a demo
protocol to verify proper instrument operation. Run the check protocol
(.check_96dw_tip, .check_kf_tip, .check_pcr_tip, or check_24dw_tip)
under the

Maintenance

menu according to the KingFisher Flex head

and plastics you are using. If the check is all right, proceed with your
own runs.

This section describes how to refit both the transport locks, the
transport lock of the heating block and that of the tip comb holder.

To refit the transport lock of the heating block, follow these steps:

1.

Remove the heating block in the following way:

•

First choose the .chang

e_heatblock protocol.

•

Then press

START

.

•

Remove the heating block by pulling it out.

•

Press the

START

key when the task has been completed.

2.

Switch off the power.

3.

Take the transport lock screw from its storage site.

4.

Insert the transport lock screw into the label and refit the transport
lock of the heating block into its place (Figure 3–25).

Figure 3–25.

Refitting the transport lock of the heating block (A)

How to pack the

instrument for

transportation

How to refit the

transport lock of the

heating block

«
...
39
40
41
42
43
...
»

Summary of Contents for KingFisher Flex





































































































































































































































Reviews:

No comments

Related manuals for KingFisher Flex

Brand: Ecco Pages: 4

Brand: DAPAudio Pages: 16

Brand: 3M Pages: 28

Brand: Jacobsen Pages: 6

Brand: Abbott Pages: 2

FreeStyle Libre

Brand: Abbott Pages: 3

Brand: abc Pages: 8

Brand: dbx Pages: 2

Growers Supply 109722

Brand: FarmTek Pages: 9

Brand: WalkMed Pages: 2

Brand: Walinga Pages: 20

Brand: Tar River Pages: 26

Brand: ZOLL Pages: 38

Brand: ZOLL Pages: 36

Nature2 Fusion soft

Brand: Zodiac Pool Systems Pages: 52

Brand: G21 Pages: 7

Brand: LSI Pages: 24

Levitator III F-LHLEV3

Brand: Skytron Pages: 248

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands