Thermo Scientific KingFisher Flex Service Manual Download Page 37 | Manualshive

Page: 37 / 228

background image

Installation

Installation setups

Thermo Fisher Scientific

Thermo Scientific KingFisher

®

Flex User Manual

31

Figure 3–20.

Shield plate fitted

There are four kinds of interchangeable KingFisher Flex heads available,
for KingFisher 24 Deep Well plates, Microtiter 96 Deep Well plates,
KingFisher 96 plates, and PCR plates. The KingFisher Flex heads all
have corresponding disposable plastic tip combs (Table 3–2). Note that
KingFisher Flex heads do not fit into the KingFisher 96 and vice versa.

Caution

Do not place the KingFisher Flex heads on top of the

instrument or any metal surfaces.
Keep the KingFisher Flex heads always in their respective plastic boxes
when not in use.
It is very important to keep the KingFisher Flex heads away from each
other and other magnets at all times. Clashing of the magnets together
may cause serious damage to the magnets.

▲

Interchangeable

KingFisher Flex heads

«
...
35
36
37
38
39
...
»

Summary of Contents for KingFisher Flex





































































































































































































































Reviews:

No comments

Related manuals for KingFisher Flex

Brand: GE Pages: 24

Brand: Cadman Pages: 66

D-MAS HyperSat 2540

Brand: DanMedical Pages: 103

Brand: Zell Pages: 32

Brand: Uflex Pages: 16

Air 2000 Outdoor

Brand: ubbink Pages: 21

Brand: Gaspardo Pages: 44

Brand: Fast Pages: 60

Brand: Lalizas Pages: 12

BOBCAT 130 Series

Brand: Balcrank Pages: 12

Brand: Marcy Pages: 9

Retractable Box Scrapers HR3584

Brand: Land Pride Pages: 1

Brand: ATD Tools Pages: 7

SPLICE-500 MKII

Brand: Serpent Pages: 8

Brand: Wecan Technology and Lighting Co., Ltd Pages: 4

Brand: ABB Pages: 136

Brand: ABB Pages: 108

Brand: Beckman Coulter Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands