Thermo Scientific AI 3000 Operating Manual Download Page 59

Page: 59 / 108

Installation

Installing the Sampling System Support on the TRACE 1300/TRACE 1310

Thermo Scientific

AI 3000/AS 3000 Sampling System - Operating Manual

Figure 36.

Assembling (2)

3. Guide the three fixing screws into the corresponding fixing holes located on the GC top.

See A’, B’, and C’.

4. Tighten the three fixing screws.

5. If not already done, mount and fix the guide pivot on each top plate by using the proper

fixing screw.

6. Place the two top plates over the double bottom plate.

7. Guide each retainer and its fixing screw into the sliding slot present on each top plate.

8. Align each retainer fixing screw into the corresponding fixing hole located on the double

bottom plate.

9. Tighten each retainer fixing screw to block the corresponding upper plate to the double

bottom plate.

A’

B’

C’

Top Plate Back

Double Bottom Plate

Retainer

Guide Pivot

Top Plate Front

Retainer

Summary of Contents for AI 3000













































































































Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands

Thermo Scientific AI 3000, Operating Manual

Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands