Thermo Scientific AI 3000 Operating Manual Download Page 50

Page: 50 / 108

Installation

Installing the Sampling System Support on the TRACE 1300/TRACE 1310

AI 3000/AS 3000 Sampling System - Operating Manual

Thermo Scientific

Figure 30.

Assembling on the Front Injector Module (2)

4. Place the L-shape bottom plate on the GC top and guide the three fixing screws into the

corresponding fixing holes. See A’, B’, and C’.

5. Tighten the three fixing screws.

6. If not already done, mount and fix the guide pivot on the top plate by using the proper

fixing screw.

7. Place the top plate over the L-shape bottom plate.

8. Guide the retainer and its fixing screw into the sliding slot present on the top plate.

9. Align the retainer fixing screw into the corresponding fixing hole located on the L-shape

bottom plate.

10. Tighten the retaining fixing screw.

11. Clamp the two plates by using the plates locking screw.

Retainer

Top Plate

L-shape Bottom Plate

B’

Guide Pivot

A’

C’

Summary of Contents for AI 3000













































































































Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands

Thermo Scientific AI 3000, Operating Manual

Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands