Thermo Scientific AI 3000 Operating Manual Download Page 41

Page: 41 / 108

Installation

Sampling System Support

Thermo Scientific

AI 3000/AS 3000 Sampling System - Operating Manual

Sampling System Support

The AI 3000/AS 3000 II is installed on the GC using the appropriate support provided.

According to your GC, please refer to:

•

Sampling System Support for TRACE 1300/TRACE 1310

•

Sampling System Support for TRACE GC Ultra

•

Sampling System Support for FOCUS GC

Sampling System Support for TRACE 1300/TRACE 1310

The AI 3000/AS 3000 II can be installed only on the

right

side of the GC on the

front

back

injector module or on both when in

Gemini

configuration by using the proper sampling

system support.

The sampling unit support consists of a bottom and a top plates.

1. The bottom plate can be

L-shape

(see both front/back installation) or

double

(see

Gemini installation). The plate is provided with a series of holes for the corresponding
fixing screws and must be fixed on the GC.

2. The movable top plate is mounted over the bottom plate and it is provided with a guide

pivot for the accommodation and centering of the sampling unit. The movable top plate
can slides over the bottom plate through a sliding slot and a retainer.

This allows moving away the injection device of the sampling unit from the injector
module when the latter will require maintenance.

To use the proper sampling system support on the TRACE 1300/TRACE 1310 please refer
to:

•

Support for the Installation on the Front/Back Injector Module

•

Support for the Installation in Gemini Configuration

•

Support for the Installation When a TSQ Quantum Mass Spectrometer is Coupled with
the GC

Note

The FOCUS GC MS Version, may accept the AI 3000/AS 3000 II also on the left

side. Please refer to

“Assembling of the Sampling System Support on FOCUS GC MS

Version”

page 46

To reduce the FOCUS GC working area, the AS 3000 may be installed as described in

“Space Saving Installation”

page 47

Note

After the installation of the sampling unit on the proper sampling system

support, it is possible locking its plates if desired.

Summary of Contents for AI 3000













































































































Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands

Thermo Scientific AI 3000, Operating Manual

Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands