Thermo Scientific AI 3000 Operating Manual Download Page 68

Page: 68 / 108

Installation

Installation of the AI 3000/AS 3000 II on the GC

AI 3000/AS 3000 Sampling System - Operating Manual

Thermo Scientific

3. Check the correct alignment of the sampling system support, then fix it by tightening the

proper fixing screws.

4. Insert the sample tray into the sampling unit base.

•

AI 3000

— insert the 8-position sample tray into the appropriate housing of the

sampling unit base. See

Figure 44

Figure 44.

8-position Sample Tray

•

AS 3000

— insert the dedicated support plate into its appropriate housing of the

sampling unit base. Place the 105-position sample tray on the hub located on the
support. The system will automatically recognize the sample tray at the instrument
power on. See

Figure 45.

105-position Sample Tray

8-position Sample Tray

Support Plate

105-position Sample Tray

Hub

Summary of Contents for AI 3000













































































































Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands

Thermo Scientific AI 3000, Operating Manual

Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands