Thermo Scientific AI 3000 Operating Manual Download Page 49

Page: 49 / 108

Installation

Installing the Sampling System Support on the TRACE 1300/TRACE 1310

Thermo Scientific

AI 3000/AS 3000 Sampling System - Operating Manual

Assembling of the Sampling System Support on the Front Injector Module

The following is the description of how to mount the sampling system support on the

front

injector module of the TRACE 1300/TRACE 1310. See

Figure 29

and

Figure 30

Figure 29.

Assembling on the Front Injector Module (1)

1. Remove from the GC top cover the three plastic caps covering the corresponding fixing

holes. See A, B, and C.

2. Orient the L-shape bottom plate to align the three installation holes to the corresponding

fixing holes located on the GC top.

3. Insert the provided fixing screws into the holes present on the L-shape bottom plate.

Note

In comparison with the installation on the back injector module, the

installation on the front injector module requires to upturn the L-shape bottom plate
before fixing it on the GC.

L-shape Bottom Plate

Summary of Contents for AI 3000













































































































Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands

Thermo Scientific AI 3000, Operating Manual

Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands