Thermo Scientific AI 3000 Operating Manual Download Page 44

Page: 44 / 108

Installation

Sampling System Support

AI 3000/AS 3000 Sampling System - Operating Manual

Thermo Scientific

Sampling System Support for TRACE GC Ultra

The support for the installation of the AI 3000/AS 3000 II on

right

left

side of the

TRACE GC Ultra consists of a semi-circular plate resting on three spacers non adjustable in
height, see

Figure 25

. The top surface of the plate is provided with two slots for corresponding

fixing screws. In the middle the guide pivot allows the accommodation and centering of the
sampling unit.

Figure 25.

Support for the Installation of the AI 3000/AS 3000 II on the TRACE GC Ultra

The AI 3000/AS 3000 II is installed on the

right

left

side of the TRACE GC Ultra.

Installation on the Right Side

When installing the AI 3000/AS 3000 II on the TRACE GC Ultra

right side

, the support is

directly mounted on the GC top panel previous installation of the spacer inside the GC. See

Figure 25

Installation on the Left Side

When installing the AI 3000/AS 3000 II on the TRACE GC Ultra

left side

, before to mount

the sampling system support, the support bracket must be placed and fixed on the GC top
cover. See

Figure 26

Note

For details about the installation of the spacer, please refer to

“Installing the Spacer

Inside the GC”

page 43

for details.

1 = Semi-circular Plate

2 = Guide Pivot

3 = Spacers

4 = Slots

5 = Fixing Screws

Summary of Contents for AI 3000













































































































Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands

Thermo Scientific AI 3000, Operating Manual

Search results

Summary of Contents for AI 3000

Reviews:

Related manuals for AI 3000

Brands by name

Popular brands