Thermo Scientific A55867 User Manual Download Page 28 | Manualshive

Page: 28 / 198

background image

Installing the instrument

Prepare bench space to receive the DynaCellect

™

instrument unit (see “Instrument dimensions”

) ensuring that there is easy access to the “On/Off” switch and mains IEC connector at the rear

of the instrument.

CAUTION!

The DynaCellect

™

instrument should be installed on a stable bench. If a mobile set up is

used, it is the user’s responsibility to ensure that all safety hazards and functional risks are addressed
including adequately supporting the weight of the instrument and having sufficient wheel span so that
both the trolley and instrument are stable.

·

Ensure that the bench is stable and level to within ±0.4" (10 mm).

·

Position the instrument on the bench with a minimum of 4" (10 cm) between the rubber feet and
the edges of the bench.

CAUTION!

·

The DynaCellect

™

instrument weighs 49.75 kg (109.7 lbs) (50.6 kg/111.6 lbs with poles and bag

hangers). Use appropriate care and seek assistance if necessary when lifting or moving the
instrument. Use the holding recess to lift the instrument.

·

Do not position the instrument is such a way that it would make it difficult to disconnect the power
cord from the power inlet.

Installation

1.

Find the 2 pole extensions and 2 pole adaptors.

2

1

1

Pole adaptor

2

Pole extension

Chapter 2

Installation and setup

Installing the instrument

2

28

CTS

™

DynaCellect

™

Magnetic Separation System User Guide

«
...
26
27
28
29
30
...
»

Summary of Contents for A55867







































































































































































































Reviews:

No comments

Related manuals for A55867

Brand: ABB Pages: 18

Brand: R-Tech Pages: 3

Brand: Cadman Pages: 66

Brand: Panasonic Pages: 180

Brand: idiag Pages: 10

Versaflo S Series

Brand: 3M Pages: 11

DBI Sala EXOFIT

Brand: 3M Pages: 32

Brand: 3M Pages: 8

Brand: Accurate Bio-Medical Technology Pages: 35

Brand: vanEE Pages: 52

Brand: Caddon Hives Pages: 3

Brand: Idex Pages: 141

Brand: IDEAL Networks Pages: 8

Brand: IDEAL Networks Pages: 5

ThermoTweez Handpiece TT-65

Brand: Pace Pages: 14

Brand: ProLights Pages: 28

Brand: Jenx Pages: 34

Brand: KaVo Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands