Thermo Scientific A55867 User Manual Download Page 148 | Manualshive

Page: 148 / 198

background image

CAUTION!

The Single-Use Kit has been designed exclusively for use with the DynaCellect

™

instrument and includes several features to enable fast, error-free loading by the user. It is the
responsibility of the user to ensure correct assembly and loading of the Single-Use Kit prior to
initiating an instrument protocol.

CAUTION!

Only use kits supplied by Thermo Fisher Scientific or its agents.

CAUTION!

Inspect each Single-Use Kit for any damage or imperfections that may result in

incorrect operation. Do not use kit if any such defect is found.

Install CTS

™

DynaCellect

™

Bead Removal Kit on the

instrument

The installation of the CTS

™

DynaCellect

™

Bead Removal Kit is similar to the CTS

™

DynaCellect

™

Cell

Isolation Kit except for the placement of tubes in the tube guide. As shown in the following figure, there
are two tubes to the reaction bag on the bead removal kit (the isolation kit has one tube to the reaction
bag).

1.

Route bead removal bag and tubes behind the left pole.

2.

Unlock the lid from eGUI and place the bead removal bag in the nest.

Chapter 6

Basic instrument operation

Install CTS

™

DynaCellect

™

Bead Removal Kit on the instrument

6

148

CTS

™

DynaCellect

™

Magnetic Separation System User Guide

«
...
146
147
148
149
150
...
»

Summary of Contents for A55867







































































































































































































Reviews:

No comments

Related manuals for A55867

Brand: Cadman Pages: 66

Brand: Oberheim Pages: 40

Brand: Rainbow Pages: 18

Brand: Haki Pages: 24

Brand: Dakota Digital Pages: 5

Brand: Yamaha Pages: 5

Brand: Lindab Pages: 12

Brand: Zero Moustique Pages: 24

Brand: Ledj Pages: 16

Brand: TREND NETWORKS Pages: 186

Brand: Metrix Pages: 21

Brand: dosatron Pages: 19

Brand: VeloFox Pages: 30

IRmadillo ASM0627-09-Z-Cx-O-G-D2x

Brand: Keit Pages: 43

Brand: S&P Pages: 4

Brand: HQ Power Pages: 9

Advanced Melting Point Apparatus

Brand: VWR Pages: 17

Brand: Calnex Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands