Terex Genie S-80 SC Operator'S Manual Download Page 51

Page: 51 / 78

Second Edition • Second Printing

Operator's Manual

Operating Instructions

Part No. 1311085GT

-80 XC

™

• S

-85 XC

™

To Steer

1 Press down the foot switch.
2 Slowly move the drive control handle in the

direction indicated by blue or yellow triangles

OR press the thumb rocker switch located on

top of the drive control handle.

Use the color-coded direction arrows on the

platform controls and the drive chassis to identify

the direction the wheels will turn.

To Drive

1 Press down the foot switch.
2 Increase speed: Slowly move the control

handle off center.
Decrease speed: Slowly move the control

handle toward center.
Stop: Return the control handle to center or

release the function enable switch.

Use the color-coded direction arrows on the

platform controls and the drive chassis to identify

the direction the machine will travel.
Machine travel speed is restricted when the boom

is raised.

Driving on a slope

Determine the uphill, downhill and side slope

ratings for the machine and determine the slope

grade.

Maximum slope rating, platform

downhill (gradeability):

S-80/85 XC

4WD: 45% (24°)

Maximum slope rating, platform

uphill:

S-80/85 XC

4WD: 45% (24°)

Maximum side slope rating:

S-80/85 XC

25% (14°)

Note: Slope rating is subject to ground conditions

with one person in the platform and adequate

traction. Additional platform weight may reduce

slope rating. The term gradeability applies to the

counterweight uphill configuration only.
Be sure the boom is below horizontal and the

platform is between the non-steer wheels.
Move the drive speed select switch to machine on

incline symbol.

Summary of Contents for Genie S-80 SC















































































Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands

Terex Genie S-80 SC, Operator'S Manual

Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands