Terex Genie S-80 SC Operator'S Manual Download Page 67

Page: 67 / 78

Second Edition • Second Printing

Operator's Manual

Maintenance

Part No. 1311085GT

-80 XC

™

• S

-85 XC

™

Maintenance

Observe and Obey:



Only routine maintenance items specified in

this manual shall be performed by the

operator.



Scheduled maintenance inspections shall be

completed by qualified service technicians,

according to the manufacturer’s specifications

and the requirements specified in the

responsibilities manual.



Use only Genie approved replacement parts.

Maintenance Symbols Legend

The following symbols have been used in this

manual to help communicate the intent of the

instructions. When one or more of the symbols

appear at the beginning of a maintenance

procedure, it conveys the meaning below.

Indicates that tools will be required to

perform this procedure.

Indicates that new parts will be required to

perform this procedure.

Indicates that a cold engine is required

before performing this procedure.

Check the Engine Oil Level

Maintaining the proper engine oil level is essential

to good engine performance and service life.

Operating the machine with an improper oil level

can damage engine components.
Note: Check the oil level with the engine off.
1 Check the oil level dipstick. Add oil as needed.

Perkins 404D-22T Engine

Oil type

15W-40

Oil type - cold conditions

5W-40

Perkins 404F-E22TA Engine

Oil type

15W-40

Oil type - cold conditions

5W-40

Deutz TD2011 L04i Engine

Oil type

15W-40

Oil type - cold conditions

5W-40

Deutz TD2.9L Engine

Oil type

15W-40

Oil type - cold conditions

5W-40

Deutz TCD 2.2L Stage V Engine

Oil type

15W-40

Oil type - cold conditions

5W-40

Summary of Contents for Genie S-80 SC















































































Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands

Terex Genie S-80 SC, Operator'S Manual

Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands