Terex Genie S-80 SC Operator'S Manual Download Page 62

Page: 62 / 78

Operator's Manual

Second Edition • Second Printing

Operating Instructions

-80 XC

™

• S

-85 XC

™

Part No. 1311085GT

Installation of Padding

1 Install the 2 pieces of padding on the platform

rails. Position the padding to protect the

panels from contact with the platform rails.

Installation of Strap

1 Open the clamp and install it around a vertical

platform rail tube.

2 Insert a bolt with a washer through one side of

the clamp.

3 Install the strap assembly end plate onto the

bolt.

4 Insert the bolt through the other side of the

clamp.

5 Secure with a washer and a nut. Do not over-

tighten. The strap assembly end plate should

be able to slide on the platform rail.

Panel Cradle Operation

1 Secure both panel cradles to the platform.
2 Place the load so that it rests in both panel

cradles.

3 Center the load on the platform.
4 Secure the load to the platform using the

strap. Tighten the strap.

Summary of Contents for Genie S-80 SC















































































Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands

Terex Genie S-80 SC, Operator'S Manual

Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands