Terex Genie S-80 SC Operator'S Manual Download Page 68

Page: 68 / 78

Operator's Manual

Second Edition • Second Printing

Maintenance

-80 XC

™

• S

-85 XC

™

Part No. 1311085GT

Diesel Fuel Requirements

Satisfactory engine performance is dependent on

the use of a good quality fuel. The use of a good

quality fuel will give the following result: long

engine life and acceptable exhaust emissions

levels.
Minimum diesel fuel requirements for each engine

are listed below.

Perkins 404D-22T Engine

Fuel Type

Low Sulfur Diesel (LSD)

Perkins 404F-E22TA Engine

Fuel Type

Ultra Low Sulfur Diesel (ULSD)

Deutz D2011 L04i Engine

Fuel Type

Low Sulfur Diesel (LSD)

Deutz TD2.9L Engine

Fuel Type

Ultra Low Sulfur Diesel (ULSD)

Deutz TCD 2.2L Stage V Engine

Fuel Type

Ultra Low Sulfur Diesel (ULSD)

Check the Hydraulic Oil Level

Maintaining the hydraulic oil at the proper level is

essential to machine operation. Improper hydraulic

oil levels can damage hydraulic components. Daily

checks allow the inspector to identify changes in

oil level that might indicate the presence of

hydraulic system problems.
1 Be sure that the boom is in the stowed

position.

2 Visually inspect the sight gauge located on the

side of the hydraulic oil tank.

Result: The hydraulic oil level should be within

the top 2 inches / 5 cm of the sight gauge.

3 Add oil as needed. Do not overfill.

Hydraulic oil specifications

Hydraulic oil type

Chevron Rando HD equivalent

Summary of Contents for Genie S-80 SC















































































Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands

Terex Genie S-80 SC, Operator'S Manual

Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands