Terex Genie S-80 SC Operator'S Manual Download Page 4

Page: 4 / 78

Operator's Manual

Second Edition • Second Printing

Introduction

-80 XC

™

• S

-85 XC

™

Part No. 1311085GT

Platform controls symbology and related

machine movement:

Platform level

Platform rotate

Jib boom up/down

Boom up/down

Boom extend/retract

Turntable rotate

Drive forward/reverse

Steer right/left

Ground controls symbology and related

machine movement:

Platform level, jib boom

up/down, boom

extend/retract,and boom

up/down

Turntable rotate and

platform rotate

Sequential functions and movement:

•

Drive and steer.

Interlocked functions:

•

Elevated drive speed.

•

Elevated drive in an off-level condition.

•

Drive enable when the boom is rotated past the

non-steer wheels.

•

All platform and ground controls.

Limitations of use:

•

The intended use of this machine is to lift

personnel, including tools, and materials to an

aerial work site.

•

Do not elevate the platform unless the machine

is on firm level ground.

Stability enhancing means:

•

Foam filled tires (if equipped).

Restricted operating envelope:

•

1,000 lbs/454 kg platform capacity.

Summary of Contents for Genie S-80 SC















































































Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands

Terex Genie S-80 SC, Operator'S Manual

Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands