Terex Genie S-80 SC Operator'S Manual Download Page 71

Page: 71 / 78

Second Edition • Second Printing

Operator's Manual

Specifications

Part No. 1311085GT

-80 XC

™

• S

-85 XC

™

Specifications

Model

S-80 XC

Height, working maximum

86 ft 26.21 m

Height, platform maximum

80 ft 24.38 m

Horizontal reach, platform

maximum

68 ft 6 in 20.88 m

Maximum load capacity

660 lbs

300 kg

Maximum load capacity, restricted 1,000 lbs

454 kg

Maximum wind speed

28 mph 12.5 m/s

Platform rotation

160°

Platform leveling

self-leveling

Turntable rotation (degrees)

360° continuous

Turntable tailswing

5 ft 3 in

1.6 m

Height, stowed maximum

9 ft 2 in

2.8 m

Length, stowed

37 ft 1 in 11.23 m

Width, standard tires

8 ft 2 in

2.49 m

Wheelbase

9 ft 4 in

2.85 m

Ground clearance, center

15.8 in

40 cm

Ground clearance, axle

13 in

33 cm

Turning radius (inside)

12 ft

3.66 m

Turning radius (outside)

21 ft 6 in

6.55 m

Platform dimensions,

6 foot (length x width)

72 in x 30 in 183 cm x 76 cm

Platform dimensions,

8 foot (length x width)

96 in x 36 in 244 cm x 91 cm

Ambient operating temperature

-20° F to 120° F

-29° C to 49° C

Controls

12V DC proportional

AC outlet in platform

standard

System voltage

12V

Hydraulic pressure, maximum

(boom functions)

2,900 psi

200 bar

Tire size

18-625, 16 ply FF

Fuel tank capacity

35 gallons 132 liters

Hydraulic tank capacity

40 gallons 151 liters

Weight

37,000 lbs 16,783 kg

(Machine weights vary with option configurations. See

serial label for specific machine weight.)

Airborne noise emissions

Sound pressure level at ground workstation

87 dBA

Sound pressure level at platform workstation

77 dBA

Guaranteed sound power level

109 dBA

Total vibration value to which the hand/arm system is

subjected does not exceed 2.5 m/s

Highest root mean square value of weighted

acceleration to which the whole body is subjected does

not exceed 0.5 m/s

Maximum slope rating, stowed position, 4WD

Platform uphill

30% (17°)

Platform downhill

45% (24°)

Side slope

25% (14°)

Note: Slope rating is subject to ground conditions with

one person in the platform and adequate traction.

Additional platform weight may reduce slope rating.

Maximum allowable

chassis inclination

Refer to "Tilt Sensor

Activation Settings" section

Drive speeds

Drive speed, stowed

3.0 mph

40 ft/9.1 sec

4.8 km/h

12.2 m/9.1 sec

Drive speed, raised or

extended

0.5 mph

40 ft/54 sec

0.8 km/h

12.2 m/54 sec

Floor loading information

Tire load maximum

19,380 lbs

8,791 kg

Tire contact pressure

130 psi

9.14 kg/cm

896 kPa

Occupied floor pressure

370 psf

1,809 kg/m

17.74 kPa

Note: Floor loading information is approximate and does

not incorporate different option configurations. It should

be used only with adequate safety factors.
Continuous improvement of our products is a Genie

policy. Product specifications are subject to change

without notice or obligation.

Summary of Contents for Genie S-80 SC















































































Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands

Terex Genie S-80 SC, Operator'S Manual

Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands