Terex Genie S-80 SC Operator'S Manual Download Page 30

Page: 30 / 78

Operator's Manual

Second Edition • Second Printing

Controls

-80 XC

™

• S

-85 XC

™

Part No. 1311085GT

Platform Control Panel

1 Horn button

Press this button and the horn will sound.

Release the button and the horn will stop.

2 Platform level switch

Move the platform level

switch up and the level of the

platform will raise. Move the

platform level switch down

and the level of the platform

will lower.

3 Platform rotate switch

Move the platform rotate

switch to the left and the

platform will rotate left.

Move the platform rotate

switch to the right and the

platform will rotate right.

4 Jib boom up/down switch

Move the jib boom switch

up and the jib boom will

raise. Move the jib boom

switch down and the jib

boom will lower.

5 Glow plug indicator light

Light on indicates the glow plugs are on.

6 Fault indicator light

Light on indicates a system fault.

7 Restricted range of motion indicator light,

weight.

Light on indicates restricted

range of motion due to platform

weight.

8 Platform overload indicator light

Light flashing indicates the platform is

overloaded. The engine will stop and no

functions will operate. Remove weight until the

light goes off and then restart the engine.

9 Restricted range of motion indicator light,

slope.

Light on indicates restricted

range of motion due to slope

angle.

10 Machine on incline indicator light

Light on indicates the tilt sensor activation

settings have been exceeded. See the

instructions in the Operating Instructions

section.

Summary of Contents for Genie S-80 SC















































































Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands

Terex Genie S-80 SC, Operator'S Manual

Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands