Terex Genie S-80 SC Operator'S Manual Download Page 70

Page: 70 / 78

Operator's Manual

Second Edition • Second Printing

Maintenance

-80 XC

™

• S

-85 XC

™

Part No. 1311085GT

Check the Tire Pressure

Note: This procedure does not need to be

performed on machines equipped with foam-filled

tires.

Bodily injury hazard. An over-inflated tire can

explode and may cause death or serious

injury.

Tip-over hazard. Do not use temporary flat tire

repair products.

To safeguard maximum stability, achieve optimum

machine handling and minimize tire wear, it is

essential to maintain proper pressure in all air-

filled tires.
1 Check each tire with an air pressure gauge.

Add air as needed.

High flotation tire pressure

100 psi 6.9 bar

Scheduled Maintenance

Maintenance performed commissioning, quarterly,

annually and every two years must be completed

by a person trained and qualified to perform

maintenance on this machine according to the

procedures found in the service and maintenance

manuals for this machine.
Machines that have been out of service for more

than three months must receive the quarterly

inspection before they are put back into service.

Summary of Contents for Genie S-80 SC















































































Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands

Terex Genie S-80 SC, Operator'S Manual

Search results

Summary of Contents for Genie S-80 SC

Reviews:

Related manuals for Genie S-80 SC

Brands by name

Popular brands