Temtrol SERIES ITF Instruction Manual Download Page 60

Page: 60 / 82

FWR/FWT 10

Page

Temtrol, Inc

Manufacturers of ….. Customized Air Handling Units

(F) MAINTENANCE

(1) Monthly:

a. Motors are equipped with permanently sealed bearings and

do not

require lubrication.

b. Check fan wheel / cone for alignment – possible: binding noise or wheel rubbing against

cone.

See “Fan Wheel/Cone Alignment” section.

(2) Every Six Months:

a. Check motor bearings for possible binding, noise or overheating.

b. Check supply fan and exhaust fan wheels for dirt and grease accumulation. Clean as

necessary. Do not use caustic cleaning solutions.

(3) Yearly:

a. Lightly lubricate damper bushings and associated linkage (Ruskin - Back Draft Damper).

(4) Every Two Years:

a. Examine unit housing for signs of corrosion. Clean, replace or touch up with paint
as necessary.

FWR

FWT

Summary of Contents for SERIES ITF



















































































Search results

Summary of Contents for SERIES ITF

Reviews:

Related manuals for SERIES ITF

Brands by name

Popular brands

Temtrol SERIES ITF, Instruction Manual

Search results

Summary of Contents for SERIES ITF

Reviews:

Related manuals for SERIES ITF

Brands by name

Popular brands