background image

LCD 63SE (VG) Keypad 

User Manual 

13 

Disarming Both partitions A and B

Voice Messages in Disarming Mode 

(LCD 63VG SE)

A continuous beep indicates the entrance time . The voice messages “

System is armed

” and “

Please, 

enter your code to disarm

” will sound on every 5 seconds . 

After a valid code has been entered, the message “

System is disarmed

” will be repeated twice . 

If no valid code has been entered during entry time, the “

System is armed

” message will sound .

If an alarm has been triggered in the system, the messages “

Alarm in the system

” and “

Please, enter 

your code to disarm

” will be repeated every 5 seconds .

Stopping the alarm

The alarm is stopped by entering a valid personal code with assigned rights to operate with both 

Partitions in the system . 

ATTEnTIon: If you cannot stop the alarm using a valid user with assigned rights to operate 

with both partitions, call the Engineer and your system technical support! 

panic Buttons

Press and hold the  

 + 

 buttons for 2 seconds, to send an alarm signal to the control panel . 

The option not sounding the siren when using the panic buttons is programmed from the engineer .

Ambush Code

Ambush code is a personal code that disarms the system, but still sends alarm signal to a Central 

monitoring station . Its purpose is to indicate that the user is forced to disarm the system against his 

will .

The ambush code is produced from a personal code by increasing the last number by one . If the last 

number is 9, it is replaced by 0 in the ambush code .

Example:

  

Personal code: 4615 → Ambush code: 4616

 

 

Personal code: 4619 → Ambush code: 4610

entry

time

code

Note: 

To the user code are assigned rights to operate with 

both Partitions A and B, otherwise the system will DISARM 

only  that  Partition  for  which  the  User  code  are  assigned 

rights!

Summary of Contents for LCD 63SE

























Reviews: