Calibration—7623/R7623
Service
l. CHECK/ADJUST- Check
High Speed Mesh for
13
volts.
Adjust R1393 High Speed Mesh adjustment
for 13
volts.
m.
Press the
single sweep reset on the horizontal
time-base
plug-in unit.
n.
Remove
the transistor Q1
788.
o.
Press
the
ERASE button.
p.
CHECK
-Storage
test points (see Fig. 2-10). Table
2-8
lists the
storage test points and their tolerances.
Connect
the test oscilloscope 10X probe to each test point,
in turn, setting
the deflection factor to 1.0 V, 2.0 V, and
5.0 V
as
required.
TABLE
2-8
Test
Points
Tolerance
High Speed Mesh
+120
V
to
+130 V
ce
3
+81 V
to +88 V
ce
2
+81 V
to +88 V
CE,
+81
V to +88 V
FGA
+86 V
to +93 V
FGK
Less than 500 mV
q.
CHECK/ADJUST-Check
Collector
for 120 volts.
Adjust R1439 collector adjustment for +120 volts.
r.
Replace transistor Qi 788.
45.
Check—
Erase
and
Fast Transfer Pulses
a.
Connect
10X probe from test oscilloscope to
the
Bi-Stable
test
point.
b.
Press
the
ERASE button.
c.
CHECK—
Test
oscilloscope display for erase and
transfer waveforms. See
Fig. 2-11A
and B for
typical
waveforms.
d. CHECK-Transfer
pulse amplitude is greater than
+540 volts above
ground.
e.
CHECK Erase
pulse amplitude
is approximately 320
volts
above
ground.
f.
CHECK -That
erase ramp is less than 375 ms long,
and
that the ramp starts at zero volt level or below.
46.
Check—
High
Speed
Mesh Pump
Pulses
a. Set
the test
oscilloscope to 5.0 V/division
vertical
deflection (50 V/divison
at probe tip), and a sweep rate of
1.0
microsecond.
b.
Connect
the test probe
to the High Speed Mesh test
point.
c.
Press
ERASE
button (do not transfer or store a
display).
d.
CHECK/ADJUST-Check
that the pump pulses
are
2.0
µs
wide (top of pulse
only). Adjust pump pulse width
R1559 for
2.0 µs
at the
top of the pulse.
47.
Check
Pump
Pulse
Frequency
a. Set
test oscilloscope sweep rate to
5.0 millisecond/
division.
b.
CHECK—For
five
pump pulses in eight div1.2
divisions
(100
Hertz ±15%).
48.
Check/Adjust
STORAGE
LEVEL
Range
a.
Set STORAGE
LEVEL control fully clockwise.
b. Set AUTO VIEWTIME fully
clockwise
and press the
AUTO
ERASE button.
c. Set horizontal time base plug-in unit for
0.1 micro
second.
d.
CHECK/ADJUST—Check that only
the center of the
storage
screen saturates during the store time.
Adjust
STORAGE
LEVEL range adjustment
R.1440 so that only
the center screen
saturates.
2-30
Summary of Contents for 7623
