Calibration
—7623/R7623
Service
h. Set
the time-mark generator for both one- and
0.1
-millisecond
markers.
i. Position the
baseline
of the markers as far toward the
bottom
of the graticule as possible
with the calibration
fixture
Position control.
j.
CHECK—Vertical bowing and tilt of the
marker
display for
less than
0.1 division (each 0.1-millisecond
marker represents 0.1 division).
k.
ADJUST-Geometry
adjustment R1184 (see Fig. 2-2)
for
minimum bowing for time markers.
Adjustment may
have
to
be compromised to obtain less than
0.1 division
bowing and
tilt everywhere within the graticule area.
9.
Check
External
Z-Axis
Operation
a.
Install
the
7A15A
in the right vertical compartment.
b.
Connect the
output of the
medium-frequency
constant-amplitude signal generator
to
the
input of the
7A15A
through
the five-nanosecond GR cable, 50-ohm GR
in-line
termination,
and
the BNC T connector.
c.
Set
the 7A15A
for
a deflection factor of one
volt/division.
d.
Set
the 7B53A
for auto, internal
triggering at a
calibrated
sweep rate of 10 microseconds/division.
e.
Set the
medium-frequency generator for a two-
division
display at its
reference frequency (50 kilohertz).
f.
Connect
the
output of the BNC T connector to the
EXT
Z-AXIS connector
with the
42-inch 50-ohm BNC
cable.
g.
CHECK—Top portion
blanked
out.
of
displayed
waveform
h.
Disconnect cable from
external Z-AXIS CON
NECTOR.
10.
Check
Beam
Finder
a.
Set
the 7A15A deflection factor to 20 millivolts/
division. Notice that the
display exceeds the viewing
area.
b.
Press
the BEAM
FINDER switch.
c. CHECK-Display compressed within graticule area.
d.
Increase the
7A15A
deflection factor-
until the
compressed
display
is reduced in amplitude.
e. Release the BEAM
FINDER switch.
f.
CHECK-Display remains within graticule area.
g.
Disconnect all
test
equipment and remove the plug-in
units.
2-11
Summary of Contents for 7623
