Maintenance-7623/R7623
Service
A.
Unsolder all of the power
transformer wires
connected
to
the top of the
board. Use
a vacuum-type
desoldering
tool
to remove the solder from the hole
in the
circuit board.
5. Remove
the screws holding each corner of the board
to
the chassis.
6.
To
replace the Rectifier board, reverse the order
of
removal. Be sure that
all
of the transformer wires are
properly
placed before
resoldering. Match the
arrows on the
multi pin connectors to the
arrows
on the board. Correct
location
of
the pin connectors
and the wire color code is
shown on
the circuit board illustration in the
Diagrams
section.
G. CALIBRATOR
BOARD
REPLACEMENT.
1.
Unsolder
power on/off indicator.
2.
Remove FOCUS,
INTENSITY, BEAM FINDER and
GRATICULE
ILLUM
knobs.
3.
Remove securing
nut
which holds INTENSITY and
GRATICULE ILLUM control
to front panel.
4.
Disengage
the power switch actuating rod from the
coupler.
Remove
the rod and plastic bushing through the
front
of
the instrument.
5.
Remove
two screws holding the VERT MODE switch
to the front sub-panel.
6.
Remove
the screw holding the calibrator board to the
support on the
CRT
shield.
7. Pull
the Calibrator board out far enough
to allow the
multi-pin
connectors and wire leads to be disconnected
from the
Calibrator board (note the wire color code).
8. Remove the board.
9.
To
replace the
circuit board, reverse the removal
procedure. Match
the arrows on the multi-pin connectors to
the
arrows on the
circuit board.
Plug-In
Interface Connectors. The individual contacts of
the
plug in interface connectors can be replaced.
However,
it
is recommended that
the entire Main Interface board be
replaced if
a
large
number of the contacts are damaged. An
alternative
solution is to
refer the maintenance of the
damaged Main Interface board to
your local TEKTRONIX
Field
Office
or
representative. Use the following procedure
to
replace
an individual contact of the plug-in interface
connector.
1.
Remove
the
Main
Interface circuit board from the
instrument
as described
previously.
2.
Snap
the connector cover (white plastic) off the side
of the
plug-in interface
connector which needs repair.
3.
Unsolder and
remove the damaged contact.
4. Install
the replacement contact. Carefully form it
to
the
required
shape to fit against the connector body.
5.
Snap the
connector cover
back onto the plug-in
interface
connector. Check that the
contact which was
replaced
is aligned with the other contacts.
6.
Replace the
Main Interface board.
Access
To
The
Fan
Motor
1.
Remove
the four screws holding the Low-Voltage
Regulator sub assembly to the main
chassis (see Fig. 4-7).
2.
Pull
the Low-Voltage regulator sub-assembly
out
through
the
rear
of the instrument as far as cables will
permit.
3. Remove
the
two screws holding
the motor to the
bracket; be
careful
not
to lose the spacers between the
motor and the bracket.
4.
To
replace the motor, reverse the order of removal.
Access
To
The Fan Motor For
The
R7623
1.
Remove the
eight
screws holding the Signals-Out rear
panel
to the chassis. Pull rear
panel out as far as cables will
permit
(see
Fig. 4 8).
2.
Remove
the four
corner bolts securing the
motor to
the
chassis.
3. To replace
the motor, reverse
the order of
removal.
Fig. 4-7.
Location of screws holding Low Voltage sub chassis.
4-13
Summary of Contents for 7623
