Calibration
—
7623/R7623
Service
TRIGGERING
SYSTEM
Equipment
Required
1.
Mainframe standardizer calibration fixture
3.
7A15A plug-in unit
2. 7B53A plug-in unit
4.
8NC to pin-jack cable
Control
Settings
g.
Set the VERT MODE switch to RIGHT.
Set the
controls as given in
the Preliminary Control
Settings.
h.
Set
the calibration fixture Test switch to VERT or
HORIZ
+ STEP RESP, REP RATE switch to 250 Hz, and
adjust
the
Amplitude control for a two-division display.
Position
the
display in the lower half of the graticule area.
21.
Check
Trigger
Source
Operation
i.
Set the VERT MODE switch to ALT.
a.
Install the mainframe standardizer calibration fixture
in
the right vertical compartment and the 7A15A in the left
vertical
compartment.
j.
CHECK-CRT
display; both square-wave displays
are
stable.
b. Install
the 7853A
in the horizontal compartment.
k. Set the TRIG SOURCE switch
to LEFT.
c.
Set
the 7B53A for auto, internal triggering at a sweep
rate
of 0.5 millisecond/division.
I
.
CHECK-CRT display; Calibrator display only is
stable.
d.
Set
the 7A15A for a deflection factor of 0.2
volt/division.
m.
Set the TRIG SOURCE switch to RIGHT.
e.
Connect the 0.4 V Calibrator
pin-jack to the input of
the 7A15A with the BNC to pin-jack cable.
n. CHECK-CRT display; only
the calibration fixture
display is stable.
f.
Position
the Calibrator waveform display in the upper
half of
the graticule
area with the 7A15A Position control.
o.
Disconnect the BNC to pin-jack cable and remove the
plug-in
units.
2-16
Summary of Contents for 7623
