Borroughs BASIC PRO SERIES Assembly Instructions Manual Download

Page: 1 / 17

BASIC PRO-SERIES WORKBENCH

SECTION #1

CONTENTS

Basic Pro-Series…………………………………………2

Roller Bearings………………………………………….11
Lift Cabinet……………………………………………...12

Continuous Pro-Series…………………..……… ….…14

IMPORTANT - PRODUCT LIABILITY

INFORMATION

Read all instructions before

proceeding with installation. Vital product

information pertaining to proper set-up and

cautions are included. Failure to follow these

instructions may result in personal injury and/or

property damage.

RETAIN THIS MANUAL FOR FUTURE

REFERENCE

NOTICE:

Borroughs Corporation extends to the original purchaser from the date of purchase, a 5

year limited warranty against manufacturing defects in material and workmanship. If a Borroughs

product fails to perform because of a manufacturing defect, Borroughs will examine it. If found

defective, it will be repaired at our option. This warranty applies only to Borroughs products acquired

directly from Borroughs Corporation or from Authorized Borroughs Dealers. This warranty does not

apply to any product which has been subject to misuse, negligence, or accident; has been damaged in

shipment, storage, or installation; has been misapplied or has been modified or repaired by

unauthorized persons or been repaired with non-standard Borroughs replacement parts. This warranty
specifically excludes claims for indirect, incidental, or consequential damages arising in any way from a

product defect. This warranty is exclusive, and exists in lieu of all other warranties, either express or

implied. This warranty gives you specific legal rights; you may also have other rights which may vary

from state to state. To obtain warranty service, contact your Borroughs Selling Dealer. You must make

a written claim. Provide a copy of your purchase record and a written description of the warranty

problem with your claim. If you are unable to contact your dealer, contact: Borroughs Corporation,

Customer Service Manager, 3002 N. Burdick Street, Kalamazoo, MI 49004-3483

3002 N. BURDICK ST.

▪

KALAMAZOO, MI 49004-3483

09-50679-00

800-748-0227

▪

FAX: 269-342-4161

▪

www.borroughs.com

November 2004

Summary of Contents for BASIC PRO SERIES


















Search results

Summary of Contents for BASIC PRO SERIES

Reviews:

Related manuals for BASIC PRO SERIES

Brands by name

Popular brands

Borroughs BASIC PRO SERIES, Assembly Instructions Manual

Search results

Summary of Contents for BASIC PRO SERIES

Reviews:

Related manuals for BASIC PRO SERIES

Brands by name

Popular brands