Calibration
—
7623/R7623
Service
VERTICAL
DEFLECTION
SYSTEM
Equipment
Required
6.
Five-nanosecond G R cable
1.
Mainframe standardizer calibration fixture
7.
50-ohm GR in-line
termination
2.
7B53A plug-in unit
8.
BNC to pin-jack cable
3.
High-frequency generator
9.
Dual-input coupler
4.
7A15A plug-in unit (two)
10.
Three-inch screwdriver
5.
10X probe
11.
Low-capacitance screwdriver
Control
Settings
12.
Adjust
Vertical
Centering
Set
the
controls as given in the
Preliminary Control
Settings.
a.
Set
the
calibration fixture
Test switch to
TRIG
GERING
GAIN.
11.
Adjust
Bias
Adjustment
a. Install the 7B53A
in the horizontal compartment.
b.
Set
the 7B53A
for auto, external triggering
at a
sweep rate of one millisecond/division.
b.
The
trace should be within 0.3 division
of the
graticule center line.
c.
ADJUST-Vertical
Centering
adjustment R403 (see
Fig. 2-3) to
position the
trace to the center horizontal line.
c.
Install
the mainframe standardizer calibration fixture
in
the left vertical compartment. Set the calibration fixture
Test
switch to VERT
or HORIZ Gain
and the Rep Rate
switch
to 250 kHz.
d.
ADJUST—
Bias R486 for maximum
gain. (See
Fig.
2-3.)
13.
Adjust Vertical
Gain
a.
Set
the calibration fixture Test switch to VERT or
HORIZ
GAIN.
b. Position the
display so that the
first and seventh
traces are near
the top and bottom
lines
of the graticule.
c. CHECK—Deflection between
the second and sixth
traces should
be six divisions
±0.06 division.
d. ADJUST-Vertical
Gain adjustment R447 (see
Fig.
2-3)
for exactly
six divisions of deflection between the
second and sixth traces.
e.
Remove the calibration fixture
from the left vertical
compartment
and install it
in the right vertical compart
ment.
f.
Set
the VERT MODE switch to RIGHT.
{
Fig. 2-3.
Location of Vertical System adjustments (Vertical Output
board).
g. CHECK—Deflection between
the second and
sixth
traces should
be the same as part c or d ±1%.
2-12
Summary of Contents for 7623
