TDK-Lambada HWS?HWS, User Manual, Page: 62 / 133

62
・All specifications are subject to change without notice.
Instruction Manual
HWS
HWS HD
HWS ME
HWS-P
ITEMS/UNITS
MODEL
HWS600-5/ME HWS600-12/ME HWS600-15/ME HWS600-24/ME HWS600-48/ME
Input
Voltage Range (*3) V AC85 - 265 or DC120 - 330
Frequency (*3) Hz 47 - 63
Power Factor (100/200VAC)(typ) (*2) 0.99 / 0.95
Efficiency (100/200VAC)(typ) (*2) ％ 80/83 81/84 82/85 83/86
Current (100/200VAC)(typ) (*2) A 7.5/3.6 8.1 / 3.9
Inrush Current (100/200VAC)(typ) A 20 / 40
Leakage Current (*11) mA Less than 0.5. (0.12 (typ) at 100VAC / 0.34 (typ) at 230VAC)
Output
Nominal Voltage VDC 5 12 15 24 48
Maximum Current (*1) A 120 53 43 27 (31) 13
Maximum Power W 600 636 645 648 624
Maximum Line Regulation (*6) mV 20 48 60 96 192
Maximum Load Regulation (*7) mV 30 72 90 144 288
Temperature Coefficient (%) Less than 0.02% / ° C
Maximum Ripple & Noise (0≤Ta≤70 ° C) (*5) mVp-p 120 150 350
Maximum Ripple & Noise ( − 10≤Ta< 0 ° C) (*5) mVp-p 180 200 400
Hold-up Time (typ) (*10) ms 20
Voltage Adjustable Range VDC 4.0 - 6.0 9.6 - 14.4 12.0 - 18.0 19.2 - 28.8 38.4 - 52.8
Function
Over Current Protection (*8) A >126 >55.7 >45.2 >31.4 >13.7
Over Voltage Protection (*9) VDC 6.25 - 7.25 15.0 - 17.4 18.8 - 21.8 30.0 - 34.8 55.2 - 64.8
Remote Sensing Possible
Remote ON/OFF Control Possible
Parallel Operation Possible
Series Operation Possible
Monitoring Signal PF (Open collector output)
Line DIP Designed to meet SEMI-F47 (200VAC Line only)
Environment
Operating Temperature (*12) ℃ -10 to +70 (-10 - +50: 100%, +70: 50%)
Storage Temperature ℃ -30 to +85
Operating Humidity ％ RH 10 - 90 (No dewdrop)
Storage Humidity ％ RH 10 - 95 (No dewdrop)
Vibration
At no operating, 10 - 55Hz (sweep for 1min)
19.6m/s² constant, X,Y,Z 1hour each.
Shock (In package) Less than 196.1m/s²
Cooling Forced air by blower fan
Isolation
Withstand Voltage
Input - FG : 2.5kVAC (20mA), Input - Output : 3kVAC (20mA)
Output - FG : 500VAC (100mA), Output - CNT : 100VAC (100mA) for 1min
Isolation Resistance
More than 100M Ω Output - FG : 500VDC
More than 10M Ω Output - CNT : 100VDC at 25 ° C and 70%RH
Standards
Safety Standards (*13) Approved by UL60601-1, EN60601-1, CSA-C22.2 No601.1-M90
PFHC Designed to meet IEC61000-3-2
Voltage Fluctuations / Flicker Emissions Designed to meet IEC61000-3-3
EMI Designed to meet EN55011/EN55022-A, FCC-A, VCCI-A
Immunity
Designed to meet IEC61000-4-2(Level 3), -3(Level 3), -4(Level 3),
-5(Level 3,4), -6(Level 3), -8(Level 4), -11
Mechanical
Weight (typ) g 1600
Size (W x H x D) mm 100 x 82 x 165 (Refer to outline drawing)
(*1) ( ): Peak output current at 200VAC. Operating time at peak output is less than 10 sec, duty is less than 35%.
(*2) At 100/200VAC, Ta=25
°
C and maximum output power.
(*3) For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 - 240VAC (50/60Hz).
(*4) Not applicable for the inrush current to noise filter for less than 0.2ms.
Inrush current is 30A (typ) when PFHC start-up.
(*5) Measure with JEITA RC-9131A probe, bandwidth of scope: 100MHz.
(*6) 85 - 265VAC, constant load.
(*7) No load - full load, constant input voltage.
(*8) Constant current limit with automatic recovery.
Avoid to operate at over load or short circuit condition for more than 30 seconds.
(*9) OVP circuit will shut the output down, manual reset (CNT reset or re-power on).
(*10) At 100/200VAC, nominal output voltage and maximum output current.
(*11) Measured by the each measuring method of UL, EN, and CSA (at 60Hz), Ta=25 ° C.
When using it as a patient care equipment, all outer surfaces of the equipment shall be
constructed of nonconductive material. See clause 19.5DV.2 of UL60601-1.
(*12) Ratings - Derating at standard mounting. Refer to output derating curve.
- Load (%) is percent of maximum output power or maximum output current, whichever is greater.
(*13) As for UL60601-1, EN60601-1 and CSA-C22.2 No601.1-M90, basic insulation.
Please refer to "TDK-Lambda
EMC Filters" catalog.
●Recommended EMC Filter
RSEN-2006L
HWS
600/ME
HWS600/ME Specifications
(Read instruction manual carefully, before using the power supply unit.)