TDK-Lambada HWS?HWS, User Manual, Page: 44 / 133

Please refer to "TDK-Lambda
EMC Filters" catalog.
●Recommended EMC Filter
RSEN-2016
HWS
1000/HD
ITEMS/UNITS
MODEL HWS1000
-3/HD
HWS1000
-5/HD
HWS1000
-6/HD
HWS1000
-7/HD
HWS1000
-12/HD
HWS1000
-15/HD
HWS1000
-24/HD
HWS1000
-36/HD
HWS1000
-48/HD
HWS1000
-60/HD
Input
Voltage Range (*2) V AC85 - 265 or DC120 - 330
Frequency (*2) Hz 47 - 63
Power Factor (100/200VAC)(typ) (*1) 0.98/0.95
Efficiency (100/200VAC)(typ) (*1)
％
71/73 76/78 79/81 80/82 82/85 83/85 85/87 85/88 86/88 85/88
Current (100/200VAC)(typ) (*1) A 9.6/5.0 13.5/7.0
Inrush Current (100/200VAC)(typ) (*3) A 20/40
Leakage Current (100/240VAC) (*10) mA 1.2 max
Output
Nominal Voltage VDC 3.3 5 6 7.5 12 15 24 36 48 60
Maximum Current A 200 167 134 88 70 46 30.7 23 18.4
Maximum Peak Current (*13) A - 160 100 80 58.5 39 29.2 23.4
Maximum Power W 660 1000 1002 1005 1056 1050 1104
Maximum Peak Power (*13) W - 1200 1404
Maximum Line Regulation (*5) mV 20 36 48 60 96 144 192 240
Maximum Load Regulation (*6) mV 40 60 100 120 150 300 360
Temperature Coefficient Less than 0.02% /
℃
Maximum
Ripple & Noise (*4)
0 to +71
℃
mVp-p 120 150 200 400
-10 to 0
℃
mVp-p 160 180 240 500 600
Hold-up Time (typ) (*9) ms 20
Voltage Adjustable Range VDC 2.64-3.96 4.0-6.0 4.8-7.2 6.0-9.0 9.6-14.4 12.0-18.0 19.2-28.8 28.8-43.2 38.4-52.8 48.0-66.0
Function
Over Current Protection (*7) A >210.0 >175.3 >168.0 >105.0 >84.0 >61.4 >40.9 >30.6 >24.5
Over Voltage Protection (*8) VDC 4.12-4.62 6.25-7.0 7.5-8.4 9.37-10.5 15.0-17.4 18.7-21.8 30.0-34.8 45.0-49.7 55.2-60.0 69.0-75.0
Remote Sensing Possible
Remote ON/OFF Control Possible
Parallel Operation Possible
Series Operation Possible
Monitoring Signal PF(Open collector output)
Line DIP Built to meet SEMI-F47 (200VAC Line only)
Other Function PCB Coating on solder side and component side.
Environment
Operating Temperature (*11)
℃
-10 to + 71, Guarantee Start up -40 to -10
-10 to +40 ° C
％
100
+50 ° C
％
83.9 100
+71 ° C
％
50
Storage Temperature
℃
-40 to +85
Operating Humidity
％
RH 10 - 90 (No Condensing)
Storage Humidity
％
RH 10 - 95 (No Condensing)
Vibration (*14)(*15)
At no operating, 10 - 55Hz (Sweep for 1min.) 19.6m/s² Constant, X,Y,Z 1hour each.
Designed to meet MIL-STD-810F 514.5 Category 4 figure 514.5C-1, category 10
Shock (In package) (*15) Less than 196.1m/s² Designed to meet MIL-STD-810F 516.5 Procedure I
Cooling Forced Air By Blower Fan
Isolation
Withstand Voltage
Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA)
Output - FG : 500VAC (300mA), (60V model 651VAC(390mA)), Output - CNT:100VAC (100mA) for 1min.
Isolation Resistance
More than 100M
Ω
Output - FG : 500VDC
More than 10M
Ω
Output - CNT : 100VDC at 25
℃
and 70%RH
Standards
Safety Standards (*12) Approved by UL60950-1, CSA C22.2 No.60950-1, EN60950-1, EN50178. Built to meet DENAN.
PFHC Built to meet IEC6100-3-2
EMI Built to meet EN55011/EN55022-B, FCC-ClassB, VCCI-ClassB, CISPR-ClassB.
Immunity Built to meet IEC61000-4-2(Level 2,3), -3(Level 3), -4(Level 3), -5(Level 3,4), -6(Level 3), -8(Level 4), -11
Mechanical
Weight (max) g 3200
Size (W
×
H
×
D) mm 126.5 x 82 x 240 ( Refer to outline drawing )
(*1) At Ta=25
℃
and maximum output power.
(*2) For cases where conformance to various safety specs (UL, CSA,EN) are required, input voltage range will be 100 - 240VAC(50/60Hz).
(*3) First in-rush current. Not applicable to the first 0.2ms in-rush current flowing into the power supply noise filter.
(*4) Measure with JEITA RC-9131A probe, Bandwidth of scope :100MHz. (at 100uF electric capacitor and 0.47uF film capacitor on the test fixture board.)
(*5) 85 - 265VAC , constant load.
(*6) No load-Full load, constant input voltage.
(*7) Constant current limit with automatic recovery. Over current condition for more than 5 seconds will cause the out-
put to shutdown. Output current exceeding maximum rated output current for more than 10 seconds continuously
will result to output shutdown.
(*8) OVP circuit will shut down output, manual reset (Power cycle) or ON/OFF CNT signal reset.
(*9) At 100/200VAC, nominal output voltage and maximum output current.
(*10) Measured by the each measuring method of UL, CSA, EN and DENAN(at 60Hz), Ta=25
℃
.
(*11) Ratings - Derating at standard mounting.
- Load (%) is percent of maximum output power or maximum output current,whichever is greater.
- As for other mountings, refer to derating curve.
- For conditions of start up at -40
℃
to 10
℃
, refer to derating curve.
(*12) As for DENAN,built to meet at 100VAC.
(*13) Peak output current is less than 10 seconds, and duty 35% max.(200VAC Line only)
(*14) Category 4 exposure levels : Truck transportation over U.S. highways, Composite two-wheeled trailer.
(*15) It is compulsory to fix BRACKET onto product for MIL-STD-810F 516.5 Procedure
Ⅰ
and MIL-STD-810F 514.5 category 10 compliance.
Refer to mounting method.
HWS1000/HD Specifications
(Read instruction manual carefully, before using the power supply unit.)
Please refer to page 50 for MIL-STD Mounting
44
・All specifications are subject to change without notice.
Instruction Manual
HWS
HWS HD
HWS ME
HWS-P