TDK-Lambada HWS?HWS, User Manual, Page: 14 / 133

14
・All specifications are subject to change without notice.
Instruction Manual
HWS
HWS HD
HWS ME
HWS-P
HWS80 Specifications
(Read instruction manual carefully, before using the power supply unit.)
ITEMS/UNITS
MODEL
HWS80-3 HWS80-5 HWS80-12 HWS80-15 HWS80-24 HWS80-48
Input
Voltage Range (*2) V AC85 - 265 or DC120 - 370
Frequency (*2) Hz 47 - 63
Power Factor (100/200VAC)(typ) (*1) 0.98 / 0.90 0.99 / 0.95
Efficiency (100/200VAC)(typ) (*1) ％ 77 / 79 82 / 85 83 / 85 84 / 86
Current (100/200VAC)(typ) (*1) A 0.72 / 0.36 1.04 / 0.52
Inrush Current (100/200VAC)(typ) (*3) A 14 / 28, Ta=25 ℃ , cold start
Leakage Current (*10) mA Less than 0.5. (0.2 (typ) at 100VAC / 0.4 (typ) at 230VAC)
Output
Nominal Voltage VDC 3.3 5 12 15 24 48
Maximum Current A 16 6.7 5.4 3.4 1.7
Maximum Power W 52.8 80 80.4 81 81.6
Maximum Line Regulation (*5) mV 20 48 60 96 192
Maximum Load Regulation (*6) mV 40 96 120 192 384
Temperature Coefficient Less than 0.02% / ℃
Maximum Ripple & Noise (0≤Ta≤70 ℃ ) (*4) mVp-p 120 150 200
Maximum Ripple & Noise ( − 10≤Ta< 0 ℃ ) (*4) mVp-p 160 180 240
Hold-up Time (typ) (*9) ms 20ms
Voltage Adjustable Range VDC 2.97 - 3.96 4.0 - 6.0 9.6 - 14.4 12.0 - 18.0 19.2 - 28.8 38.4 - 52.8
Function
Over Current Protection (*7) A >16.8 >7.04 >5.67 >3.57 >1.79
Over Voltage Protection (*8) VDC 4.13 - 4.95 6.25 - 7.25 15.0 - 17.4 18.8 - 21.8 30.0 - 34.8 55.2 - 64.8
Remote Sensing Possible
Remote ON/OFF Control Possible (/R Option)
Parallel Operation -
Series Operation Possible
Line DIP Built to meet SEMI-F47 (200VAC Line only)
Environment
Operating Temperature (*11) ℃ -10 to +70 (-10 to +50: 100%, +60: 60%, +70: 20%)
Storage Temperature ℃ -30 to +85
Operating Humidity ％ RH 30 - 90 (No dewdrop)
Storage Humidity ％ RH 10 - 95 (No dewdrop)
Vibration
At no operating, 10 - 55Hz (sweep for 1min)
19.6m/s² constant, X, Y, Z 1hour each.
Shock (In package) Less than 196.1m/s²
Cooling Convection cooling
Isolation
Withstand Voltage
Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA)
Output - FG : 500VAC (100mA) for 1min
Isolation Resistance More than 100M Ω at 25 ℃ and 70%RH Output - FG : 500VDC
Standards
Safety Standards (*12)
Approved by UL60950-1, CSA C22.2 No.60950-1, EN60950-1, EN50178 UL508 (with cover models only),
CSA C22.2 No.14-M95 (with cover models only) Built to meet DENAN
PFHC Built to meet IEC61000-3-2
EMI Built to meet EN55011/EN55022-B, FCC-B, VCCI-B
Immunity
Built to meet IEC61000-4-2(Level 2,3), -3(Level 3), -4(Level 3),
-5(Level 3,4), -6(Level 3), -8(Level 4), -11
Mechanical
Weight (typ) g 450
Size (W x H x D) mm 28 x 82 x 160 (Refer to outline drawing)
(*1) At 100/200VAC, Ta=25
℃
and maximum output power.
(*2) For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 - 240VAC (50/60Hz).
(*3) Not applicable for the in-rush current to noise filter for less than 0.2ms.
(*4) Measure with JEITA RC-9131A probe, bandwidth of scope : 100MHz.
(*5) 85 - 265VAC , constant load.
(*6) No load-full load, constant input voltage.
(*7) Constant current limit and hiccup with automatic recovery. Not operate at over load or
dead short condition for more than 30 seconds.
(*8) OVP circuit will shutdown output, manual reset (re power on).
(*9) At 100/200VAC, nominal output voltage and maximum output current.
(*10) Measured by the each measuring method of UL, CSA, EN and DENAN (at 60Hz).
(*11) Ratings - Derating at standard mounting.
- Load (%) is percent of maximum output power or maximum output current, whichever is greater.
- As for other mountings, refer to derating curve.
(*12) As for DENAN, built to meet at 100VAC.
Please refer to "TDK-Lambda
EMC Filters" catalog.
●Recommended EMC Filter
RSEL-2002W
HWS
80