TDK-Lambada HWS?HWS, User Manual, Page: 46 / 133

ITEMS/UNITS MODEL
HWS1500
-3/HD
HWS1500
-5/HD
HWS1500
-6/HD
HWS1500
-7/HD
HWS1500
-12/HD
HWS1500
-15/HD
HWS1500
-24/HD
HWS1500
-36/HD
HWS1500
-48/HD
HWS1500
-60/HD
Input
Voltage Range (*2) V AC85 - 265
Frequency (*2) Hz 47 - 63
Power Factor (100/230VAC)(typ) (*1) 0.98 / 0.94
Efficiency (100/200VAC)(typ) (*1)
％
72 / 75 77 / 81 79 / 82 81 / 83 82 / 85 83 / 87 84 / 88 86 / 90
Current (100/200VAC)(typ) (*1) A 15.0 / 8.0 19.5 / 10.0 19.0 / 10.0
Inrush Current (100/200VAC)(typ) (*3) A 20 / 40
Leakage Current (100/240VAC) (*10) mA 1.5 max
Output
Nominal Voltage V 3.3 5 6 7.5 12 15 24 36 48 60
Maximum Current (100/200VAC) A 300 / 300 250 / 250 200 / 200 125 / 125 100 / 100 65 / 70 42 / 46.5 32 / 32 25.6 / 28
Maximum Peak Current (*13) A
−
300 240
−
105 70
−
42
Maximum Power (100VAC/200VAC) W 990/990 1500/1500 1560/1680 1512/1674 1536/1536 1536/1680
Maximum Peak Power (*13) W
−
1800
−
2520
−
2520
Maximum Line Regulation (*5) mV 36 40 48 60 96 144 192 240
Maximum Load Regulation (*6) mV 60 72 90 144 150 288 360
Temperature Coefficient Less than 0.02%/
℃
Maximum
Ripple & Noise
(*4)
+25 to +71
℃
mVp-p 150 200 400
0
℃
mVp-p 200 150 200 400
-10
℃
mVp-p 220 200 240 400 600
Hold-up Time (typ) (*9) ms 20 16 20
Voltage Adjustable Range VDC 2.64 - 3.96 4.0 - 6.0 4.8 - 7.2 6.0 - 9.0 9.6 - 14.4 12.0 - 18.0 19.2 - 28.8 28.8 - 43.2 38.4 - 52.8 48.0 -66.0
Function
Over Current Protection (*7) A > 315.0 > 262.5 > 210.0 > 131.2 > 105.0 > 68.2 > 44.1 > 33.6 > 26.8
Over Voltage Protection (*8) VDC 4.12 - 4.62 6.25 - 7.0 7.5 - 8.4 9.37 - 10.5 15.0 - 17.4 18.7 - 21.8 30.0 - 34.8 45.0 - 49.7 55.2 - 64.8 69.0 - 75.0
Remote Sensing Possible
Remote ON/OFF Control Possible
Parallel Operation Possible
Series Operation Possible
Monitoring Signal PF (Open collector output)
Line DIP Designed to meet SEMI-F47 (200VAC Line only)
Other Function PCB Coating on solder side and component side.
Environment
Operating Temperature (*11)
℃
-10 to +71, Guarantee start up at -40 to -10
at Input Voltage
100VAC/200VAC
-10 to +40°C W 990 1500 1560 / 1680 1512 / 1674 1536 1536 / 1680
+50°C W 825 1250 1500 1560 / 1680 1512 / 1674 1536 1536 / 1680
+60°C W 660 1000 1125 1170 / 1260 1134 / 1255 1152 1152 / 1260
+71°C W 495 750 780 / 840 756 / 837 768 768 / 840
Storage Temperature
℃
-40 to +85
Operating Humidity
％
RH 10 - 90 (No Condensing)
Storage Humidity
％
RH 10 - 95 (No Condensing)
Vibration (*14)(*15)
At no operating, 10 - 55Hz (sweep for 1min.) 19.6m/s² constant, X,Y,Z 1hour each.
Designed to meet MIL-STD-810F 514.5 Category 4 figure 514.5C-1 and Category 10
Shock (In package) (*15) Less than 196.1m/s
2
Designed to meet MIL-STD-810F 516.5 Procedure I
Cooling Forced air by blower fan
Isolation
Withstand Voltage
Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA), Output - CNT : 100VAC (100mA)
Output - FG : 500VAC (300mA), (60V model 651VAC (390mA) ) for 1min.
Isolation Resistance
More than 100M
Ω
Output - FG : 500VDC
More than 10M
Ω
Output - CNT : 100VDC at 25
℃
and 70%RH
Standards
Safety Standards (*12) Approved by UL60950-1, CSA C22.2 No.,60950-1, EN60950-1, EN50178. Designed to meet DENAN.
PFHC Designed to meet IEC61000-3-2
EMI Designed to meet EN55011/EN55022-A, FCC-ClassA, VCCI-ClassA.
Immunity
Designed to meet IEC61000-4-2(Level 2,3), -3(Level 3), -4(Level 3),
-5(Level 3,4), -6(Level 3), -8(Level 4), -11
Mechanical
Weight (typ) g 4000 3800
Size (W x H x D) mm 126.5 x 82 x 280 (Refer to outline drawing)
(*1) At Ta=25
℃
and maximum output power.
(*2) For cases where conformance to various safety specs (UL, CSA, EN) are required, input voltage range will be 100 - 240VAC (50/60Hz).
(*3) First in-rush current. Not applicable to the first 0.2ms in-rush current flowing into the power supply noise filter.
(*4) Measure with JEITA RC-9131A probe, bandwidth of scope :100MHz.
（
at 100uF electric capacitor and 0.47uF film capacitor on the test fixture board.)
Ripple noise spec for ambient temperature between -10 to 25 is a linearity value with respect to the -10 degrees C and 25 degrees C specs.
(*5) 85 - 265VAC , constant load.
(*6) No load-full load, constant input voltage.
(*7) Constant current limit with automatic recovery. Over current condition for more than 5 seconds will cause the out-
put to shutdown. Output current exceeding maximum rated output current for more than 10 seconds continuously will result
to output shutdown.
(*8) OVP circuit will shut down output, manual reset (power cycle) or ON/OFF CNT signal reset.
(*9) At 100/200VAC, nominal output voltage and maximum output current.
(*10) Measured by the each measuring method of UL, CSA, EN and DENAN (at 60Hz), Ta=25
℃
.
(*11) Ratings - Derating at standard mounting.
- Load (%) is percent of maximum output power or maximum output current, whichever is greater.
- As for other mountings, refer to derating curve.
- For conditions of start up at -40
℃
to -10
℃
, refer to derating curve.
(*12) As for DENAN, designed to meet at 100VAC.
(*13) Peak output current is less than 10 seconds, and duty 35% max.(200VAC Line only)
(*14) Category 4 exposure levels : Track transportation over U.S. highways.
(*15) It is compulsory to fix BRACKET onto product for MIL-STD-810F 516.5 Procedure
Ⅰ
and MIL-STD-810F 514.5 category 10 compliance.
Refer to mounting method.
Please refer to "TDK-Lambda
EMC Filters" catalog.
●Recommended EMC Filter
RSEN-2030
Please refer to page 50 for MIL-STD Mounting
HWS1500/HD Specifications
(Read instruction manual carefully, before using the power supply unit.)
HWS
1500/HD
46
・All specifications are subject to change without notice.
Instruction Manual
HWS
HWS HD
HWS ME
HWS-P