BRINK Series - English
2
The data described in this handbook are purely a guide. TAU reserves the right to change them in any moment.
The manufacturer reserves the right to modify or improve products without prior notice. Any inaccuracies or errors found in this handbook
will be corrected in the next edition.
When opening the packing please check that the product is intact. Please recycle materials in compliance with current regulations.
This product may only be installed by a qualifi ed fi tter. The manufacturer declines all liability for damage to property and/or
personal injury deriving from the incorrect installation of the system or its non-compliance with current law (see Machinery
Directive).
WARNINGS AND INSTRUCTIONS FOR FITTERS
Congratulations on choosing this Tau product. Please read this handbook carefully.
For the sake of simplicity, the instructions are listed in order of installation.
Please read these instructions carefully before installing the product as they contain important information concerning safety,
installation, use and maintenance.
Anything not expressly specifi ed in this handbook is FORBIDDEN.
Contact TAU srl for information regarding any points which may not
have been specifi ed in the present manual.
Operations not indicated in these instructions may damage the product and put people, animals and/or and property at risk.
The equipment should be installed only by trained and qualifi ed personnel.
Installation, electrical connections and adjustments must be made according to the rules of good workmanship and current standards.
Before beginning installation, make sure the product is undamaged.
Do not install the product in explosive environments.
Prior to installing the automation, make all structural modifi cations in order to ensure safety distances and protect and segregate areas in
which people may be exposed to the risk of crushing, shearing, dragging or similar dangers. Make sure the existing structure is suffi ciently
sturdy and stable. Observe current legislation when adjusting maximum gearmotor torque (in Europe consult prEN 12341 and prEN
12635 standards).
Apart from buried models, the gearmotor must be installed above ground level in order to prevent damage deriving from fl ooding.
The safety devices (photocells, sensitive edges, emergency stop devices, etc.) must be installed according to current legislation and
directives, the rules of good workmanship, the installation area, the operating logic of the system and the forces developed by the
powered door or gate.
Choose short routes for the cables. Keep power cables separate from control cables.
Though the gearmotor is fi tted with various safety devices, we strongly recommend keeping all unattended devices capable of opening
the gate out of the reach of children or unable adults.
Fit the signs required by current regulations for identifying dangerous areas. Each installation must show the identifi cation data of the
automated devices in a visible place.
Before connecting to the power supply, make sure the data on the rating plate correspond to the mains power supply.
Fit a multipole switch/knife switch on the power supply network with contacts opening distance of at least 3 mm.
Make sure there is a suitable circuit breaker and overcurrent protection device (thermal-magnet breaker C6) upline from the electrical
system.
Connect the automation to an effi cient earth system compliant with current safety standards.
The manufacturer declines all liability if incompatible safety and components are installed. Only use original spare parts to repair or
replace the product.
The fi tter must provide all the information relative to the automatic, manual and emergency operation of the automated unit, and give the
user the operating instructions.
Keep all the documents concerning the system inside or near the central control unit.
MAINTENANCE PROGRAM FOR SWING DOOR BRINK and BRINK-S:
Each 6 month:
! Attention
Before work on the operator cut main power line.
- Check that all securing screws are well tightened.
-
Clean and lubricate moving and sliding components.
-
Lubricate closing spring if present.
-
Check wiring connections.
-
Check that arm connection screw are well tightened.
-
Check that door leaf are stable and the movement is steady, without friction from full open to full close position.
-
Check the condition of the hinges and lubricate it.
-
Check that speeds, timing, and safety functions are well adjust.
-
Controllare che le velocità, I tempi e le funzioni di sicurezza siano ben selezionate.
-
Check that safety and activation sensor are properly functioning.
!Attention - Any part that appear damaged or worn must be changed.
For spare parts see the spare part list.
