SystemAir 247606 Operation And Maintenance Instructions Download Page 67

Page: 67 / 68

Quick configuration guide |

14.4.14.2 Operating settings

Adjust the start/stop limits for support heating/cooling and the min run time for the support control function in the

Data & Settings

Demand control

Support control

menu.

Overview:

Data & Settings

Demand control

Support Control

2021–03–01

Min time for support control

20 min

Start heating room temperature

15 °C

Stop heating room temperature

21 °C

Start cooling room temperature

30 °C

Stop cooling room temperature

28 °C

Step by step:

Select

Data & Settings

from the navigation icons

2. Select

Demand control

3. Select

Support control

4. Adjust the minimum run time in support control as

Min time for support control

5. Adjust the start and stop temperatures for support heating as

Start heating room temperature

Stop heating

room temperature

6. Adjust the start and stop temperatures for support cooling as

Start cooling room temperature

Stop cooling

room temperature

254051 | A001

Summary of Contents for 247606





































































Search results

Summary of Contents for 247606

Reviews:

Related manuals for 247606

Brands by name

Popular brands

SystemAir 247606, Operation And Maintenance Instructions

Search results

Summary of Contents for 247606

Reviews:

Related manuals for 247606

Brands by name

Popular brands