manualshive.com logo in svg

Symmetricom TimeProvider 2300, User Manual

Share
Download
Symmetricom TimeProvider 2300 User Manual Download Page 97

098-00564-000 Revision A3 – July, 2013

TimeProvider 2300/2700 User’s Guide

97

Chapter 3  

TimeProvider 2300/2700 CLI Command Set

Static mode Parameters
IP address      :    192.168.9.44
IP mask         :    255.255.255.0
IP gateway      :    0.0.0.0

Example 3:

To display the status of the Ethernet interfaces for the Ethernet management port: 

tp2700> show ip status mgmt

Response 3:

mgmt0 Link encap:Ethernet HWaddr 00:B0:AE:00:00:05

inet addr:192.168.5.14 Bcast:192.168.5.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:70867 errors:0 dropped:0 overruns:0 frame:0
TX packets:1986 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4511319 (4.3 MiB) TX bytes:162895 (159.0 KiB)
Interrupt:21 Base address:0xe000

Example 4:

To display the status of the Ethernet interfaces for the ETH2 port

tp2700> show ip status eth2

Response 4:

eth2 Link encap:Ethernet HWaddr 00:B0:AE:01:32:4A

inet addr:192.168.2.11 Bcast:192.168.2.255 
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:32 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:360 (360.0 B) TX bytes:1920 (1.8 KiB)
Interrupt:128

Level :

User, Config, and Admin

set ip

Use this command to provision the Host, Mask, and Gateway IPv4 addresses for 
the Ethernet management port and ETH1 and ETH2 ports. It also supports the DNS 
client function by provisioning the DNS server, 

Summary of Contents for TimeProvider 2300



















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands