Sym Quad Raider 600 Service Manual Download Page 96

Page: 96 / 247

8. V-BELT DRIVING SYSTEM

8-4

Loosen 1nut from the driven pulley with

Special

tool.

Tool name: Universal holder
Tool NO: SYM-2210100

Remove the drive pulley and belt.

Inspection

Check the drive belt for crack or wear. Replace it if
necessary.
Measure the width of drive belt as diagram shown.

Service Limit: 29.2 mm

Replace the belt if exceeds the service limit.

Caution

Using the genuine parts for replacement.

The surfaces of drive belt or pulley must be
free of grease.

Clean up all grease or dirt before installation.

Drive Plate

Remove the drive face.
Loosen 5 bolts from the CVT cooling plate then
remove it.

Drive face

SYM-2210100

Belt tooth

Width

To this chapter contents

Summary of Contents for Quad Raider 600
























































































































































































































































Search results

Summary of Contents for Quad Raider 600

Reviews:

Related manuals for Quad Raider 600

Brands by name

Popular brands

Sym Quad Raider 600, Service Manual

Search results

Summary of Contents for Quad Raider 600

Reviews:

Related manuals for Quad Raider 600

Brands by name

Popular brands